Jump to content
SAU Community

Recommended Posts

Hi Fellas,

I was recently having a few issues with my car with low power output. However, I change the spark plugs (Put NGK platinum ones) and the power was back up (wheels spings in 3rd gear :down: )

Anyway, 3 weeks of driving, the power is back down, had a look at the spark plugs, and they are fouled, yet again...

I cant keep forking out $150 every 3 weeks to change the spark plugs, so what do you guys suggest?

I have a built rb25/30 block, forged pistons, rods, the whole shabang. GT35r turbo, Autronic SM4.

Went to the tuner last week, AFR were perfect throughout so I am not too sure whats causing the fouling? Will I need to get hotter plugs? I am currently running the NGK PFR6G-11 5555 at 0.8 gap.

Not sure what heat rating these are.

Any suggestions are welcome.

CHeers fellas.

Link to comment
https://www.sau.com.au/forums/topic/308303-spark-plugs-keep-fouling-why/
Share on other sites

Do you have any rich spots in your tune, even small events? i.e. just coming onto boost, or injection cut on deceleration?

Are you getting any misfires, especially on boost?

as i understand it, plugs foul cos of rich condition and/or lack of spark (not igniting the mix)

maybe something to do with the gap?

with 22psi (going by whats in your sig) you might need a colder plug. most people run 6s on stock engines/lower boost.

what did your tuner have to say?

good luck bro

what kind of driving do you do?

constant short trips (5mins or so to work i the morning) when the car is cold and not hitting boost can foul plugs pretty easily...

if this is the case take it out for a nice longer drive and boost it a bit... it should clear up.

otherwise, look at your tune again... most likely too much fuel somewhere.

plugs to use would be bcpr7es @ 0.8

what kind of driving do you do?

constant short trips (5mins or so to work i the morning) when the car is cold and not hitting boost can foul plugs pretty easily...

if this is the case take it out for a nice longer drive and boost it a bit... it should clear up.

otherwise, look at your tune again... most likely too much fuel somewhere.

plugs to use would be bcpr7es @ 0.8

Pretty much 5-10 min drives to work and back each day, car doesn't even get a chance to fully warm up.

As for these bcpr7es, what heat range should I get?

How long do these spark plugs generally last?

I wouldn't mind changing them once a month, anymore than that gets annoying....

Thanks for the input :P

Pretty much 5-10 min drives to work and back each day, car doesn't even get a chance to fully warm up.

As for these bcpr7es, what heat range should I get?

How long do these spark plugs generally last?

I wouldn't mind changing them once a month, anymore than that gets annoying....

Thanks for the input :P

Theres your answer, you need to trim the temp compensation.

bcpr7es, usually 7-12 months depending on driving Kms.

the 7 in the number IS the heat range

mine last 20,000ish with 300rwkw

if your car is always on cold start / idle then try giving it a good run and boosting it for a while and see if the plugs clean up a bit.

if they do then you know which part of your tune has too much fuel

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How f**ked am i? what would happen if i leave the magnet inside there? 
    • I'll update you guys when i get home from work, im going to try to fish it out.  I just realized that i can't even drop the oil pan. The whole front diff and axles are connected to the oil pan... is it even possible to drop the oil pan without taking out the motor?  
    • So recently at the track had experienced a loss of throttle after a period of WOT after installing the emtron ecu, recently did some logging to troubleshoot the issue and found the ECU was cutting due to a low oil pressure issue. Going over the log can see that while accelerating at 4k rpm will see 100 PSI of pressure and holding steady at that level until getting off the throttle which then after can see as low as 25 PSI at 3-4k rpm and will recover back to a normal level after that.   Wondering if anyone has an idea what could be the cause as it just feels abit strange and i dont feel like it could be a sensor issues just due to it clearly sitting at a good pressure until off throttle, in the attached can see a 3rd and 4th gear pull but can even perform great through 3 and 4 gears of WOT but still once off throttle and getting back on it will see pressure drop.
    • There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
×
×
  • Create New...