Jump to content
SAU Community

Recommended Posts

hi everyone basically can anybody point out where the VCT plug is so i can diagnose if it is working or not by unplugging it and my second question is can my SAFC neo be used to control my VCT?

thanks and sorry if this has been covered before didnt find anything with SAFC and VCT

for R33 RB25DET S1.5

Edited by Pr0j3kt_Supra
Link to comment
https://www.sau.com.au/forums/topic/308386-safc-neo-vct/
Share on other sites

I'm pretty sure the SAFC is unable to control the VCT. The way VCT works is not like how V-TEC works in Hondas.

VCT on a stock car disengages aroudn 4700rpm where as in a Honda usually it engages at a higher rpm point.

Link to comment
https://www.sau.com.au/forums/topic/308386-safc-neo-vct/#findComment-5089661
Share on other sites

sorry for the confusion... ok currently the car feels sluggish with no response so i want to check where the VCT plug is i want to make sure the VCT is functioning....

second i have a safc NEO...the neo features VTEC control thoght maybe can rig it up to make it work with the nissan VCT

Link to comment
https://www.sau.com.au/forums/topic/308386-safc-neo-vct/#findComment-5090916
Share on other sites

sorry for the confusion... ok currently the car feels sluggish with no response so i want to check where the VCT plug is i want to make sure the VCT is functioning....

second i have a safc NEO...the neo features VTEC control thoght maybe can rig it up to make it work with the nissan VCT

If you're standing in front of the motor, it is on the LHS, where the plenum is.. kind of hard to explain without a photo

and yes NEO has V-TEC control but like I said before Nissan's VCT is TOTALLY different to how VTEC works, so no you cannot rig that shet up.

Car running slow? try disconnecting your SAFC, you've probably have the car running rich as.

Link to comment
https://www.sau.com.au/forums/topic/308386-safc-neo-vct/#findComment-5091063
Share on other sites

it would be strange that VCT would magically die

i dont think we see very often that VCT dies

are you sure it's just died?

has someone been fiddling and then you think it's died?

have you played around with the wiring loom before hand?

Link to comment
https://www.sau.com.au/forums/topic/308386-safc-neo-vct/#findComment-5093411
Share on other sites

just purchased the car a few days ago.... shoulda looked into it when purchasing... but yeh fed the soleniod 12V at idle and while the engine was off no click no nothing...

so this is what i know so far, the ecu is feeding the soleniod the signal (tested the plug with multimeter while reving in gear)

car drives the same plugged and un plugged( can feel power arnd the 5-6K mark but nothing before)

the soleniod is not making and noise when fed 12V

anybody have any suggestions in what else i should check? what could cause VCT death?

Link to comment
https://www.sau.com.au/forums/topic/308386-safc-neo-vct/#findComment-5094709
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Ozdavroz Not going to get a better deal than that. Cash up front and ongoing payments. 🤑
    • I wouldn't even move it like gTSBoy is saying. I'd seriously do what Duncan is saying. Unplug the injectors, and unplug the fuel pump.  Pull the spark plugs out. Have a look in quickly with a bore scope if you want. At most, you can't spray a bit of oil into the bores so there is lubricant in there while you crank it. (Don't fill it, as it's only going to enter the exhaust, or spit at you out the spark plugs holes. Before cranking the engine on the starter, after a 5 year sit I'd probably prime the oil system manually. Easiest way to do so is to look at buying an oil filter relocation block, fit it to the engine. The pressure line going into the engine on this block you can then shove into some sort of oil pump, or put it into a bottle, with that hose going to the bottom. Fill bottle up with oil. Now seal the bottle and add a compressed air line to the top of the bottle. Feed compressed air in, about 20psi will be PLENTY. This will pump oil through the motor. Be aware, it also means it will drain back to the sump, so make sure you don't end up over filling the motor Now bolt the old oil setup back on (or fully install the remote filter system).   This way you've at least pushed fresh oil everywhere, then you're letting the motor crank to then do its own oiling. Then I'd tap the key to make sure it can start to crank, if the motor free bumps, then I'd just hit the key and let it crank. After letting it crank and seeing you can get real engine oil pressure, put new spark plugs in, reconnect the fuel system electrics, and send it.   Additionally, you can look to remove the fuel feed line to the rail, and divert it to a tank so you can get the bottom of the tank shit out, and just incase there's some crud sitting anywhere that gets passed the fuel filter (or is already ahead of it).   If fuel injection at the injectors ends up appearing to be a problem, you can dump the injectors into an ultrasonic cleaner for a quick flush clean out. Note this isn't as good as new injectors, or getting them pro cleaned and flowed    
    • All I can say is, that's still bloody awesome! No plans on caging it I'm guessing?
    • It seems you'd like your Skyline to go to a great home, that can keep it as a beautiful museum piece.  I feel I can provide the perfect place for it, however, I'm not sure I can justify so much money for a Skyline that has only been crashed 3 times. Due to this and market prices, would you be against me buying it for $100.00, with $60 to be paid upfront, and the remaining $40 to be paid annually in equal payments?  
    • I did say no low balling (Insert copy and paste article from Motor mag with complete history of R32 GTR development and racing history here)
×
×
  • Create New...