Jump to content
SAU Community

Recommended Posts

-access the CONSULT port, bottom right side of dash behind flip down door.

-ignition OFF

-ground bottom middle terminal using a wire.

-ignition ON

-observe flashes (also beeps) of ABS light

-it will start with '12', (1 long flash then 2 short.)

-it will then flash the fault codes.

-to clear the codes, whilst in this diagnostic mode, disconnect the grounded terminal, then ground it 3 or more times, for at least 2 sec, within 12.5 sec. restart diagnostic mode to check if thwey have been cleared. May take a few attempts before the codes clear.

21 Front right wheel sensor (open circuit)

22 Front right wheel sensor (short - circuit)

25 Front left wheel sensor (open circuit)

26 Front left wheel sensor (short circuit)

31 Rear right wheel sensor (short circuit)

32 Rear left wheel sensor (short circuit)

35 Rear left whel sensor (open circuit)

36 Rear left whell sensor (short circuit)

41 Front right outlet solenoid valve and circuit

42 Front right inlet solenoid valve and circuit

45 Front left outlet solenoid valve and circuit

46 Front left inlet solenoid valve and circuit

55 Rear outlet solenoid valve and circuit

56 Rear inlet solenoid valve and circuit

57 Battery voltage

61 ABS actuator motor and motor relay circuit

63 ABS acutuator relay circuit

64 FR & RR G sensor 1

65 FR & RR G sensor 2

66 FR & RR sensor 1 or 2

68 G sensor voltage

69 Side G sensor voltage

71 ATTESA E_TS PRO/ABS control unit and circuit

72 Throttle position sensor

73,74 E-TS/LSD actuator motor

76,77 Pressure switch

78 Air bleed switch

79 Oil level switch

91,92,93 E-TS solenoid

94,95,96 E-TS fail safe solenoid

97,98,99 LSD solenoid

Hey Mat, welcome to SAU, and to the Stagea section of the forums.

First things first, do a quick search for your problem in this section of the forums, and you should be at least be able to find a link with info for getting ECU codes. Once you do that, see if anything matches what's previously posted. If you can't find any details about what corresponds to the codes given, post the details on here and see if anyone else can help!

yeah ive searched the forums and everything ive tried hasnt worked.

ive tried the consult port and it doesnt stop flashing i counted 102 before i gave up.

i wouldnt think a slight tire differnce would affect the system.

there is a differnce by 2.06% but wouldnt think that would be enough to affect the system??

or am i wrong?

yeah ive searched the forums and everything ive tried hasnt worked.

ive tried the consult port and it doesnt stop flashing i counted 102 before i gave up.

i wouldnt think a slight tire differnce would affect the system.

there is a differnce by 2.06% but wouldnt think that would be enough to affect the system??

or am i wrong?

From the million times this has come up on this forum, I'd say stick to the same size rims/tyres for all 4 and you wont have any problems. The ATTESA system apparently doesn't like differing rolling diameter front vs rear OR differing tyre width...it allows enough leeway for uneven tyre wear, but thats about it.

yeah ive searched the forums and everything ive tried hasnt worked.

ive tried the consult port and it doesnt stop flashing i counted 102 before i gave up.

i wouldnt think a slight tire differnce would affect the system.

there is a differnce by 2.06% but wouldnt think that would be enough to affect the system??

or am i wrong?

flat(er) tyres also cause the jerkyness and even bald vs new tyres

see if you can throw on some rims from a different car which are all identical

  • 1 month later...

yeah i thought the same thing. ive tried the consult port and i even have a cable but i dont get any fault codes,

the fault clears as soon as i turn the car off, and the light wont come back on untill i drive about 20-30km's

ive noticed a small amount of fluid araound the bottle in the boot so ill drain it and check all the lines and replace the fluid.

  • 4 weeks later...

before you do anything make sure the fluid level in the ATTESA reservoir is between full and empty, and that you don't have any leaks so that the system can pressurise.

  • 6 months later...
  • 6 months later...
  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I much prefer that to an actual oil pressure issue, never would of thought it would of been a volt drop issue but SAU brains win again. Guess ill be turning down the oil pressure limit for the track and hunting some grounds. Ill hopefully update this thread with some high oil pressure and solid ecu voltage logs. 
    • You've just discovered a really good reason to tell yourself, yes, I do need to buy an aftermarket ECU. Put the MAF in the bin. Slap in the new ECU and have a think about what turbo sounds you prefer.  Do you want a 90's style BOV wooosh? Do you want a hektik tsututututu?  Mate, can't go wrong. Just gotta get that ECU and the world is your oyster. 
    • Hi. Iam just curisou about this topic. I saw this video. It is about Greddy Type FV2. I know that BoVs are about that sound but how and when to use it? I read some topic here and from what i have understand on stock RB with MAF there will be some "problems" if you use this BoV? It vents the air in to the atmosphere and the MAF on stock car needs this air back in to the intake and not out? Or is it wrong? If so...i saw you can put some adaptor to circule air back...but does that not "loose" that sound? I saw another BoV from Turbosmart and it has two "exhaust" like ports? One is for the stock tubing for letting air back and one is for "sound" and let the air in the atmosphere? Can someone please explain? This is the Greddy one:  And this is the Turbosmart.     THANK YOU!! EDIT: So i read about this topic some more and i if i understand that correctly: That Greddy can function either like BoV or 100% Bypass valve? And that Turbosmart is what they called hybrid so you can adjust what and how many air can be vented out or back in? Is this right? THX!
    • That dirty voltage drop is the culprit I suspect 
    • i cant get them all in 1 screenshot unfortunately as i just dont know how to move things around tbh, but they are all from the same log and the line crosses at the same point for all of them
×
×
  • Create New...