Jump to content
SAU Community

Recommended Posts

hi im new here,soon installing a different turbo in my rb25det,using a gt3071r internally gated 5 bolt rear turbo with atp or whatever add on wastegate into a 4'' V band downpipe which ill make myself,any advice appreciated,i dont believe its a cropped turbine by the way.

Link to comment
https://www.sau.com.au/forums/topic/309309-hi-im-new/
Share on other sites

like do i need a manifold spacer to clear the compressor housing from the standard rb25det exhaust manifold? any images of the 90 degree outlet pipework,ive got water and oil braided hoses and a drain sorted,i need a mount for the actuator for the wastegate

Link to comment
https://www.sau.com.au/forums/topic/309309-hi-im-new/#findComment-5101262
Share on other sites

so has anybody any helpfull hints on getting this turbo in with the minimum hastle,i have a filter to instal in the braided oil lines that i have,the in line filter has -4 an male fittings on it so im not sure where to get appropiate connections to my line. ive got a 10 mm t3/4 spacer and longer studs some 90 degree hoses for the ic piping side of things,myt be a bit of fun with the inlet hose as this turbo has a 2.75 '' inlet and my car just has a standard steel internal journal bearing turbo

Link to comment
https://www.sau.com.au/forums/topic/309309-hi-im-new/#findComment-5109718
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...