Jump to content
SAU Community

Recommended Posts

These pumps need 13.5V to operate properly.

Did he wire in a new voltage feed and relay for the new pump?

The std wiring has a resistor circuit that is switched in at idle...starving the pump of voltage and starving your engine of fuel.

lol at the AFM people...he says it runs fine whether cruising or boosting so why say its the afm when it appears to be metering the air nicely.

Why ? I had a WRX thar ran faster than a mad centipede and had an idle like a roller coaster --new AFM --problem fixed.

Surely dying at idle has a limited No of causes, just go through them one by one till it's fixed (if theres no fault code)

Lets start with ;

-------------------Fuel pump.

-------------------Fuel regulator.

-------------------Fuel filter.

-------------------Dirty injectors.

:others may care to copy and paste and add other things.

OR(My choice) --- Take it to a workshop that knows WTF they're doing get a fauly code read and they'll nail the frikin thing in 5 minutes flat , pay them for the diagnostic and then fix it yourself or if it's to tricky get them to do it.

I personaly would not be friken round with the fuel system if it wasn't an easy fix, -wrong call there and bang bang engine time.

I can't understand why you're putting up with a friken spanner cowboy who seems to be learning at your expense just an IMO.

Edited by BASHO

+1. Do what you can yourself, like swapping airflow meter, replacing fuel filter, bottle of injector cleaner, then go through the harder ones with a specialist.

Only problem with that is, the experts are usually booked months in advance.

hi there guys..

firstly, thank you so much for all of your contributions.. its really nice having a place to come and get some good advise when everybody around has run out of ideas... since the poor mechanic was starting to look a bit lost, i read some more faqs on here, listened to the advise, and spent the afternoon in his workshop.. i was going to do the whole earth wire mod, but after meatering the resistance between the pump and the body, i just didnt feel confident to screw around with it.. instead is dismantled and cleaned the afm and the aac valve..his scanner showed no faults until i cleaned the afm, at which point it said it was missing or faulty.. after checking the connections again, i gave the car a run, reset his scanner and then checked it again.. scanner showed up no faults so i've been driving it ever since... so far, fingers crossed and wood-a-knockin, the car seems to be running sweet and has no more stalling..

So again, thanks guys, and if any more probs arise, i'll re-post, but in the mean time hopefully we can call this one closed...

Cheers,

Damo

you should still do the fuel pump wiring mod u dont wanna starve the engine for fuel when your giving it stick. instead of just grounding the earth wire you should put a relay in and give the pump direct battery voltage.

note - just remembered r32s dont have the battery in the boot like r33s do they? this is a piece of piss mod in 33s for your car u might have to run a wire from ur engine bay.

you should still do the fuel pump wiring mod u dont wanna starve the engine for fuel when your giving it stick. instead of just grounding the earth wire you should put a relay in and give the pump direct battery voltage.

note - just remembered r32s dont have the battery in the boot like r33s do they? this is a piece of piss mod in 33s for your car u might have to run a wire from ur engine bay.

not sure if im too keen to put the pump on a relay like that, sould be a bit scared if the relay failed.. anyway, the bloody thing started stalling again today so i dont know.. i tore the afm out and pulled it apart.. i've resoldered the joints in it.. they looked a bit old, but will try the car again tomorrow to test it.. haveb been hunting around for another afm.. the closet i can find is one of a subaru.. the unit looks identical except the green sticker on it has the very last part of the code being different.. mine is a j60, and the subaru one is an r60.. too scared to try it though incase i blow something up :D

Good to see you had a crack at fixing it yourself, If the afm is playing up, that will probably fix it.

You probably found if you wiggle the plug it came good? That is the sign of a dry solder joint. Easy fix if you have a soldering iron, and saves buying a new afm.

Good to see you had a crack at fixing it yourself, If the afm is playing up, that will probably fix it.

You probably found if you wiggle the plug it came good? That is the sign of a dry solder joint. Easy fix if you have a soldering iron, and saves buying a new afm.

cheers mate.. starting to run out of ideas if it doesnt fix it though, bad ecu anyone? yikes.. it might just be my paranoira, but im starting to think it only plays up on bloody hot days if that give anyone a clue..

not sure if im too keen to put the pump on a relay like that, sould be a bit scared if the relay failed.. anyway, the bloody thing started stalling again today so i dont know.. i tore the afm out and pulled it apart.. i've resoldered the joints in it.. they looked a bit old, but will try the car again tomorrow to test it.. haveb been hunting around for another afm.. the closet i can find is one of a subaru.. the unit looks identical except the green sticker on it has the very last part of the code being different.. mine is a j60, and the subaru one is an r60.. too scared to try it though incase i blow something up :cool:

Sometimes cleaning the AFM is only a temporary solution I know this from when I had WRX, if the car ran OK after you cleaned the AFM then went crook again could still be the AFM do you know anyone you can borrow a good one from to check it out.

:cheers:

Never owned a WRX then or you would have heard plenty :cheers:

.. well i dont have any hope of finding another skyline afm round these parts so yesterday i opened the afm and resoldered all the joints.. so far, the car seems really good so i can only hope that its sorted it.. if anything, the car seems different is a good way so far..

.. oh, and my skyline has a k&n filter in it so oil contamination was a possibility.. think the contact cleaner and resolder should be close enough to call it reconditioned :cool:....

Edited by Damo Monster
lol at the AFM people...he says it runs fine whether cruising or boosting so why say its the afm when it appears to be metering the air nicely.

Laugh all you want. I still say AFM. Its intermittent.

.. well i dont have any hope of finding another skyline afm round these parts so yesterday i opened the afm and resoldered all the joints.. so far, the car seems really good so i can only hope that its sorted it.. if anything, the car seems different is a good way so far..

.. oh, and my skyline has a k&n filter in it so oil contamination was a possibility.. think the contact cleaner and resolder should be close enough to call it reconditioned :D ....

:blush: Congrats good to hear --IMO- flick the K&N filter if it's overoiled it'll do it again , farkit flick it anyway go Apexi dry or stock--just IMO though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Use a 2' length of hose (that's 2 foot, not 2 inches) as a stethoscope to localise the source of the ticking. From cam covers? From exhaust or turbo manifold gasket? From injectors? From lower down in the engine? Etc. Use a timing light to set the timing. Put Redline Lightweight Shockproof in the box. It's not the very best thing for the box, but it will take a box that refuses to engage a gear with other oil, and make it engage a gear. I had to put it in when I installed the R33 box I have in my car. It would not select ANY gear when running. Smurf jizz made it work. That was >10 years ago and I still use it. I'm stuck with it now. Failing that - rebuild the box.
    • Well done Duncan. The fuel tank bulkhead lid is also in great condition (some of mine were stuffed). These are now out of production and good ones like that are becoming hard to come by.
    • Wow that's a steal, you've done well there. 
    • Exterior LEDs R34 2Dr R34 4Dr Position Lamp T10 T10 Winker front T20S T20S side T10 T10 rear T20S S25S150 Anti-hyfla relay TYPE3 TYPE3 tail T10 T20W Stop Lamps T20W T20W High Mount T16 T16 back T16 T20S number T10 T10 trunk T10 T10 Interior LED Item No.     Map Lamp BA9S single-sided     Room Lamps T10×31     Trunk Lamp T10     meter Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     Liquid crystal section T6.5 pedestal     Winker T6.5 pedestal     High Beam T6.5 pedestal     3 SERIES METER Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     air conditioner Early Liquid Crystal T3     Late LCD T4.2 Short     button T4.2 Middle     Hazard SW T3 Pedestal Short     Keyring T5     Cigar Socket T5
    • Howdy all,   I had my rb25det S2 rebuilt and finally started it today but have run into a few issues  Engine sounds like a a diesel easiest way to summarise like small ticking, gets louder when revs are slightly adjusted  The engine builder repainted the engine cover leaving no where for me to go off with lining up the CAS so have it as central as possible so not sure it that could be affecting it?, changed the gearbox fluid too but won’t seem to go into gear when running, and only 1 to 4 when off having a hard time finding 5th and reverse anyone got any ideas or a base for me to start off? much appreciated 
×
×
  • Create New...