Jump to content
SAU Community

Recommended Posts

Series 1 engine loom and ignitor sold.

both fan shrouds sold

alarm sold

ecu sold

gearbox sold

pivot boost guage and shift light sold

heaps and heaps of good 33 stuff still here let me know what you need.

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Noel, kinda related, but have you got any front rotors laying around? (don't want to break up your complete brake package)

No sorry Dan. Just the complete front and rear kits mate.

  • 2 weeks later...
hey bud, wat colour would the car be?

And are you from Ipswich? I think i bought a front bar off you a while back...

Car is gun metal grey and yes, that was me.

still got the headlights? what nick are they in? any pics?

headlights are sold

Are you selling the driveshaft?

If you are referring to the tailshaft it is sold.

  • 6 months later...

hey noel,

thanks for the loom, just double check the loom is for a turbo 25, as nissan are saying from their computers it is GTS25... do you know if there is any difference between the de loom & det loom

thanks again

Tyron

hey noel,

thanks for the loom, just double check the loom is for a turbo 25, as nissan are saying from their computers it is GTS25... do you know if there is any difference between the de loom & det loom

thanks again

Tyron

to the best of my knowledge the loom should be fine mate. Iif it isnt just give me a call.




  • Similar Content

  • Latest Posts

    • Yes to both! Yes to standard ECU and tune, but exhaust is aftermarket. Unsure on brand. Actually have it sitting in at my desk haha! I have to set it up on my laptop but this is a great next step, will do. So I generally try to shift before 4.5K RPM most times. I largely don't do a lot of high-rev driving, but I will take it up to red 1-2x a week max, as I know the occasional "Italian tune-up" is good for these cars.  Oh wow, is this way better than what I'm getting. Does this mean there's a good chance I have an issue?   Thanks for all the info so far guys.
    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
×
×
  • Create New...