Jump to content
SAU Community

Mid Pipe Mod A Must !

The Law

By The Law,
in R35 GTR

 Share

Recommended Posts

Martin Donnon Mentor

Martin Donnon

Posted
Posted

Run one of our WR35FS Fuel Surge tanks, allows full power at under 10 litres tank level, and can save you 50kg or so in fuel load :blush:

Thats not important to some that dont race their cars (I think GT-Ricer was being a little tongue in cheek) but it is well important to others that go racing on the odd weekend and want the fastest lap time possible :D

GT-Ricer Collaborator

GT-Ricer

Posted
Posted (edited)
.....I think GT-Ricer was being a little tongue in cheek) but it is well important to others that go racing on the odd weekend and want the fastest lap time possible :)

Tongue in cheek about weight savings ? Who, moi? Last Wednesday at EC Burrows Drive day I did 50.0 l/100 (have photo to remember it) after lunch. How long would a half full tank last? 1 session max.

I must have had a very fast, clear run because I did 1:45 when all my other laps in heavy traffic were 1:51 - 1:53. Maybe I "cheated", I am a bit dubious about my timing skills using the on-board stop watch.

Edited by GT-Ricer
Martin Donnon Mentor

Martin Donnon

Posted
Posted (edited)

Oh apologies.....I thought you were joking about saving weight and money by not running a high fuel load!

The downside to it all is that as you start to get quicker right handers will begin to cause the engine to cough and splutter from fuel surge. Been there, done that :D

Run a Driftbox, takes all the guessing out of lap times :P

Edited by Martin Donnon
  • 5 months later...
kymbo Collaborator

kymbo

Posted
Posted

Agree

Just fitted Willall mid pipe, what a difference!

Prob need to get the rest of it now, plus some bigger/ram air gear at the front. The factory scoops at the bottom are screaming out to be plumbed up and into the airbox intakes.

Anybody tried that already?

Kymbo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By MBS206 · Posted

      Well, in 2007 he must have been charging about $1800 an hour. He only looked at the car for 5 minutes. And another 4 to write the report wrong, and another minute to correct it. Mind you, this was for a car that was: Stock engine, fmic (hole in drivers guard), all alloy intake and custom air box, 3 inch turbo back exhaust, lowered, and a set of 17" Advans (255/40/17 rear and 235/45/17 front). It was nothing crazy. The blue slipper wanted the "hole in the guard" engineered. But that was because he got the shits that I wouldn't "relocate the battery from the boot, back to the factory position in the engine bay"... In an R33 GTST...     Also for emissions, E85, and don't go wild on timing. It's amazing how the closer you get ignition timing towards max torque, the last couple of degrees really throw NOx counts right up. And for the huge increase in emissions, it's only a small increase in torque.
    • MBS206
      Neil's R33 Gts-t Build

      By MBS206 · Posted

      He'll be looking down and swearing about "the damn apprentice" for trying to convince Duncan to use percussive maintenance... 😛  
    • GTSBoy
      WTB noltec r32 front upper (camber) arms

      By GTSBoy · Posted

      I swear at my GKTech ones every time I have to take them apart and replace a spherical. But I wouldn't swap them for anything else. They absolutely slay every other option, at least in terms of how they actually work. You sure you don't want to live with bearings? I mean, they don't have "ball bearings". They are rod ends and sphericals throughout. Tough as nuts, even though I have found more than one way to wear them out.
    • The Bogan
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By The Bogan · Posted

      From when I was looking at getting the 86 engineered for the turbo, the joint said to put in a few euro 5 or 6 cats, then tune the car on a nice clean E85 tune When I was looking at a turbo for the MX5, it was basically the same thing, a couple of cats and a nice clean tune Although, it will depend on the year of the Jeep IRT emmisions standards required, and what mods are done, especially if it has a newer engine installed that requires a higher Euro
    • GTSBoy
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By GTSBoy · Posted

      Yeah - but it's not actually that easy. There are limits for HC, CO, NOx and particulates. Particulates shouldn't be a concern in any petrol engine unless trying to comply to the very latest Euro standard. But getting a tune right so that all the others stay within limits AT THE SAME TIME is not a trivial exercise. You couldn't possibly get it right by just guessing at the tuner's dyno, unless he had a 4 gas analyser up the pipe, which is not often the case these days. It used to be. Every decent shop that did "tune ups" (as opposed to tuning) would have a 4 gas analsyer. Perhaps there's still quite a few of them around these days. But most "tuners" are only watching O2 and power readings.
×
×
  • Create New...