Jump to content
SAU Community

Recommended Posts

Hey guy's,

Can anyone with first hand experience please tell me the protocol with regard to driving under the rally permit scheme? I have been told you need written approval from CAMS to drive said car , say to the repairer to prepare for that event. Below is an excerpt from Vicroads:

Conditions of Use

1. A Rally Permit is a 12 month Unregistered Vehicle Permit (UVP) which permits the use of a vehicle for the following purposes:

during approved rallies conducted by a club affiliated with a national motorsport organisation approved by VicRoads

ie associated transport stages of an approved rally

travelling to or from an approved rally

in testing the vehicle for an approved rally (letter from CAMS permitting test is required)

for reasonable travel to and from a place of repair and for reasonable testing to confirm repair

2. That the operator of the vehicle must be the holder of a:

current National Rally Licence (or higher level competition licence) or;

a current International Rally Licence

an alternative competition licence approved by VicRoads.

3. That a log book of a type approved by VicRoads is also maintained and carried in the vehicle when in use (CAMS logbooks are the only approved type).

4. That the permit is not transferable.

Link to comment
https://www.sau.com.au/forums/topic/310359-rally-permit-registration-victoria/
Share on other sites

sorry, I can't help re the vic rules (i have the equivalent in nsw).

just wanted to mention that all tarmac rallies in vic run under AASA rules which will be a problem for my reading of those rules

  • 7 months later...

can i ask why you went for RP instead of normal rego?

im planning on building another 33 gtr just not sure whether to buy a complianced gtr, transfer it then cage it up, or import an unregisterable car for race use.. im assuming RP allows for uncomplianced cars ye?

My car is fully Australian compliant, was Taswegian reg, however the chap I purchased the car from wanted to send the plates in? so no way registering VICROADS therefore Rally reg the only way to go ( probably safest with regard to very occasionally driving on road (always to the mechanic, mind) and hopefully not attracting attention with the boys in blue as they will see Rally Plate and it will register to them as a rally car not a caged performance car for the streets.

If it's a genuine rally vehicle, and not just a dodgy way to drive an illegal car on the streets, then head over to BMSC to find out more. http://www.bmsc.com.au/forums/

There have been several discussions about rally rego (these are gravel cars, but the tarmac rules may be similar as far as rego goes). I know that the Vic's seem to do some weird stuff when it comes to rally cars and legislation. You're more likely to strike people who have done the hard yards over at BMSC.

My car is fully Australian compliant, was Taswegian reg, however the chap I purchased the car from wanted to send the plates in?

Was it fully registered or only SI?

If it was SI the rego is non transferable and the plates would have had to be handed in upon change of ownership.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Re read everything that has been written about this in this thread.. Let us know if you're still confused.
    • This would be a new pump with new gears. I'm just unclear on whether it's a good idea to run more oil pump flow if you don't actually need said flow. Oil level is set a minute or so after shutting off a warm engine so wouldn't the high RPM oil level in the sump end up lower all things equal? Plan is OEM clearances, main concern in my mind is whether the OEM pump can keep up with the flow requirements of any additional oil coolers.
    • Don't do what I did, use a 300000km old housing with billet gears. The old pump probably was clearanced with saw dust, Edward Lee's special engine treatment sauce and a good odo wind back. I had oil pressure issues, then replaces pump with new housing, new billet gears and 2x track day later binned a motor due to other oil related issues due to a previous engine builder. Long story short, buy a M2 or 3 or 4 N55/S55/S58 and enjoy life.
    • Yeah. "New pump" does not have to mean "massive pump".
    • Well, can you still get an OEM pump, and by the time you're buying a Nismo/N1 etc, just buy another aftermarket pump. It's better to have the pump able to flow more if its needed, than for your pressure to drop off. At any point in time, you're replacing the oil pump in a rebuild. Aftermarket pumps are likely going to be a better economical choice, and they don't have any negatives, even if they can flow more.   Also, when you're saying "replace the pump gears" are you meaning leave a 25+ year old housing in the engine with unknown wear, and just put new gears in? As that sounds silly to me, especially if you do have that minute amount of wear, that means your new pump gears now have a little bit more clearance beside them, which means, whelp, you may not get to build a lot of oil pressure or make a lot of flow.
×
×
  • Create New...