Jump to content
SAU Community

Recommended Posts

why'd you piss on his car?

virgin-boy, swap the GTS4 for a R33 N/A, straight swap.

will do

Not even. I just jokingly told him I pissed on it (I may or may not have actually done it...... :whistling:)

But yeah, he cracked it hardcore and went and dobbed me in to daddy. Came back with a smug grin on his face and said "Dad said he wants the car back within 24 hours and you've gotta look for another job"

I threatened to kill him or something (split second reaction lol) and then he walked off again :P

make amends, does bite his nails? if so, cum on his steering wheel

then find someone to fix your car

I have found someone.

It's the effort of going there which I don't have at the moment, nor buying necessary things to fix the bloody POS.

1. keep a clean record on your license

2. keep a completely stock car inside/out

3. follow road rules and behave

4. don't drive too much around areas you know are full of jap car hating cops

you'd be very unlucky if you got done

my mate drove a 400awkw rexy on his P's for 2 years and never even got pulled over

its all attitude.

in other news:

mcoupedumped-1.jpg

I drove a 250rwkw cat-less loud as f**k car with fat wheels, black windows etc and never once got pulled over. went through a few booze buses in it too and never had an issue

Might have something to do with the fact I didn't sit in a maccas carpark for fun...

Plenty I'm sure, if they check your post history, why wouldn't they be interested in buying your problem?

True that, but there's bound to be stupid arse like me out there...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...