Jump to content
SAU Community

Recommended Posts

i installed my cd player a few wks ago and whilst doing so i lost back up power, so everytime i turn the car off, everything looses memory and resets, its driving me insane.

im sure i heard a fuse blow but i cant find where, i think i have looked everywhere.

any 1 got an idea?

Link to comment
https://www.sau.com.au/forums/topic/310881-r33-looses-memory-no-back-up-power/
Share on other sites

i installed my cd player a few wks ago and whilst doing so i lost back up power, so everytime i turn the car off, everything looses memory and resets, its driving me insane.

im sure i heard a fuse blow but i cant find where, i think i have looked everywhere.

any 1 got an idea?

Mike

I'm gonna assume that you've had the memory problem since installing your CD player

the usual cause is the constant and Acc wires crossed over (there the red and yellow ones) swap them round you should be sweet

if the above assumption is wrong the the fuse is near your right knee

cheers

when you say everything, do you mean the clock in the dash as well? if so then as bundybear said, check the fuse panel on the right hand side of the steering wheel down near where the lever is to pop the bonnet. just pull them out 1 at a time and see if they are any blown.

also might be worth pulling out your stereo and just unplugging it then turning the car on and off to see if the clock is still losing it's memory.

if it is only the cd player losing it's memory then check the wiring

The same thing has happened to my R32... My cd player wont turn on at all, the clock wont display the time at all and my aircon loses its memory also. I checked the fuses and one was blown, so i tried putting another 10amp fuse in and it blows straight away. It all started when i took my car in to get the compressor bearing fixed and my mechanic has shorted something out but i cant figure what hes done.. :no:

i have checked every single fuse in the car and i cant find a blown one, the only reason my cd player is working is cause i wired constant with accessories for the time being until i find the solution, believe me i wouldnt be asking if i could find the fault.

And yes EVERYTHING looses memory, A/C, Clock, Turbo Timer, CD Player.

sly-01 which fuse keeps blowing in your r32?

mic

you've obviously lost the constant feed to the entire dash (probably ECU, dash lights also).

I know the 32'z have a fuseable link (not fuse, they look like a loop of wire) near the battery this might have gone

with no wiring diagram 4 the 33'z I'd grab a test light and start pokn round

check the back of the Ignition switch 4 constant power (make sure plugs arn't loose 2) it'l give you an idea where 2 look

where bouts you located ?? maybe someone familiar with autoelec in your area can help

cheers

ps you know there are 3 lots of fuses ....

mic

you've obviously lost the constant feed to the entire dash (probably ECU, dash lights also).

I know the 32'z have a fuseable link (not fuse, they look like a loop of wire) near the battery this might have gone

with no wiring diagram 4 the 33'z I'd grab a test light and start pokn round

check the back of the Ignition switch 4 constant power (make sure plugs arn't loose 2) it'l give you an idea where 2 look

where bouts you located ?? maybe someone familiar with autoelec in your area can help

cheers

ps you know there are 3 lots of fuses ....

yep i know there are 3 lots of fuses, under bonnet, under steering wheel and boot. i will search for that link fuse

im in mango hill, brisbane

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey, yeah I really like the color. Only paint I'd rather have is KN6, but those are expensive. Right now I'm trying to get the car to the point where I can get it tuned to 370hp so the whole setup can be driven legally, and pass the next inspection that is already due anyway. Beyond that lots of rust fixing I'm afraid, winter project is most likely going to be a front end teardown and fixing the strut tower rust. I know these can be driven daily but I don't think I will do so anytime soon. Will post a build thread soon with a list of issues and futute plans.   Cheers
    • Wanted to reply to this topic. I'm in the somewhat same boat with our Stagea. I'm trying to install a different rear diff. The Stagea/Skyline uses mounts on top of the rear diff for the ATTESA pump. Any way you can relocate the pump? I did find this kit https://theskylineshed.com/products/nissan-oem-attesa-mounting-kit-to-suit-r32-r33-r34
    • So here's the deal, my wife picked up an S2 AWD Stagea. Super cool, clean car. Looks like the owner in Japan went track spec as it's got some heavy modifications including Exedy twin disk, tension rods, coilovers, GTR brakes, oil cooler & a Nismo 2 way rear diff. Now, cool mods for sure. But, she is just using this as a casual daily driver. The 2 way rear is AGGRESSIVE. It also has solid subframe bushings & poly diff bushings. So that doesn't help either. So far I've tried changing the diff fluid to the correct fluid. Even tried a little friction modifier. No help. This thing clunks, skips the tires & has some slight whine/NVH when driving. Might sound like I'm being picky, but just trying to find a better solution. Here in the states, it's impossible to find a Stagea rear diff. No luck. I do have a 300zx non-turbo diff. Same ratio, 5 bolt axles. On the Stagea, you need both front & rear diff ratios to match. This car is a 4.083. I'd like to just swap a normal rear diff into this thing. Nothing fancy. Even open diff is fine. She's not tracking the car LOL The difference is that the ATTESA pump mounts to the top of the rear diff. There are 3 total mounting points for the pump on top of the diff. With all this being said, what would be the best way to go about this? I could remove the Stagea diff & see if I could get somebody to possibly weld the 3 tabs/mounting points onto the 300zx diff so we could mount the pump on the 300zx diff. I could swap the internals from the 300zx into the Stagea diff but this is not in my comfort zone. Is it possible to mount the ATTESA pump to the underside of the car? Sorry for the paragraph. Just trying to figure out how to go about this. Any help is much appreciated! Stagea Differential - Note two top tabs, one bolt hole for ATTESA pump mounting   300zx Diff - No mounting tabs Also found this mounting kit ?? https://theskylineshed.com/products/nissan-oem-attesa-mounting-kit-to-suit-r32-r33-r34  
    • Not ready yet, but maybe later in the year?
×
×
  • Create New...