Jump to content
SAU Community

Recommended Posts

Hey guys,

I was so excited to pick up my M35 RX Four Stagea and much enjoyed the drive back down to Geelong... Except for a few things.

1. The terrible brake shudder, braking at speeds higher than 80km. No biggie I think to myself, cos every has said it was common and just needs a skim. Ring up Nagoya motors and they said they would pay for it.

2. There seems to be a loud hum which starts around 60km/h, is loudest at 80km/h and much quieter at 100+. I did a bit of searching around on the forums and it seems it could be a wheel bearing, or I'm hoping just the tyres on the car, which from what I can tell are snow tyres (says ICE GUARD on it and has a snow flake symbol). The hum does not change pitch when cornering, and I have jiggled the wheels up on jacks and they seem fine. So fingers crossed, a tyre change will quieten things down.

3. Now this is the big one! All was good driving down to Geelong. Acceleration was strong, but turbo whine quite loud... which I've heard is normal for an M35. Then it started to make a slightly different noise, more of a screech, not real loud, but you could hear it along with the whine in the upper rev range. I started thinking... this can't be good. Sure enough, I went for a drive today to see if I could get a better listen to the screech. I started accelerating and could hear the normal turbo whine, then follwed by the screech... then nothing... the turbo went completely silent. No whine, screech, rattle... nothing! I thought this can't be good! But there should have been a loud rattle and bang or some horrendous screeching noise if the ceramic wheel broke. But I tried accelerating again and the car felt like shit and so did I....

So now it's parked back in the garage. I wouldn't mind hearing some thoughts from other people who have put in a warranty claim or going through turbo dilemas. I have a 3year/5000km warranty, but unfortunately it only covers up to $500 for turbo related problems.

I've read you can get them highflowed and stay ceramic or go steel wheeled. But apparently the steel wheeled is considerably laggier?

Sounds like time for a GCG rebuild.

$500 won't cover much unfortunately, not even a standard flow steel impellor rebuild.

Still worth a shot though, especially when the car has only been recently purchased.

Give the dealer a ring anyway and voice your displeasure, worth a shot.

Good luck!

I'd be very tempted not to accept the dealer's offer on this one. They (unlike a private seller) are required under fair trading act to make sure the "goods are fit for the purpose they are sold for". the insurance style warranty they included for $500 will not come close to covering the cost of repair (I guess around $2k).

The only option I would accept from the dealer is a replacement turbo, all at their cost. No way can they justify 2 days as being acceptable

Yep under consumer legislation in NZ they would be required to fix it (replace the turbo with a good one) or offer you the choice of another similar car or your money back. I am sure there is similar legislation in Aus which no guarantee can void. Rebuild would be around $2000 plus turbo in and out say another $500 so best dealer pays for it.

bummer mate,

i have only just bought an M35 too and was worried about this sort of thing.

hope its not too bad. whats the KMS on the clock?

Only 57000kms! Well that's what it says on the dash... but unfortunately you just never know with imports. Car looks fairly clean though.

I'd be very tempted not to accept the dealer's offer on this one. They (unlike a private seller) are required under fair trading act to make sure the "goods are fit for the purpose they are sold for". the insurance style warranty they included for $500 will not come close to covering the cost of repair (I guess around $2k).

The only option I would accept from the dealer is a replacement turbo, all at their cost. No way can they justify 2 days as being acceptable

Yeah, I thought all dealers, by law, had to have a minimum of 3months (full) warranty or something along those lines. I will definitely be trying to get them to cover the cost for a standard replacement turbo. If that does end up failing, which I think shouldn't considering the car was only just purchased, then I guess i'll just have to take the $500 plus some of my moolah and go a rebuilt turbo. I've heard it's an absolute pain to remove the turbo, but can be done without removal of engine/trans. Can someone confirm? Or say if it's just easier to remove the engine/trans? I've got access to good tools and a garage and have done 2 engine conversions, so it should be possible for me to do it, just time and effort. BUT... fingers crossed it won't come to that!

I'd be very tempted not to accept the dealer's offer on this one. They (unlike a private seller) are required under fair trading act to make sure the "goods are fit for the purpose they are sold for". the insurance style warranty they included for $500 will not come close to covering the cost of repair (I guess around $2k).

The only option I would accept from the dealer is a replacement turbo, all at their cost. No way can they justify 2 days as being acceptable

Yes the statutory warranty should still be in effect. here is a specific motor trader requirement. . I suggest you call fair trading and get them to steer you in the right direction. .even if dealer says no take them to fair trading. .you should get a fair result.

I would think the 3 month statutory warranty should cover you for the removal and rebuild of the turbo. I would be making a bit of a fuss if they try to back away from it.

To get the turbo out it will take a few hours, you will wont to unbolt the tail shaft from the gearbox and loosen the cross member holding the gearbox to get better access but it is still damn tight. (don't forget to loosen the air box before doing this)

As far as I understand the tires should have been replaced with compliance and I am reasonably sure Snow Tires would not be acceptable tires to have on your car for compliance.

Good luck.

Cheers

andy

Thanks a lot for the responses guys! Much appreciated. I feel a lot better and confident now, after reading what you guys have to say. Will definitely be kicking up a storm if they disagree and I will double check the tyres to see if they are compliant.

if your tyres are not brand new the required complancing has not taken place (for that matter the car also has to be dead stock).

I think if you suggest to the dealer that you know what you are talking about they will back down pretty quick - the new rules are very strict and they can loose their import rights if there is any suggestion that have done the wrong thing.

ie, you have "hand". use it :P

if your tyres are not brand new the required complancing has not taken place (for that matter the car also has to be dead stock).

I think if you suggest to the dealer that you know what you are talking about they will back down pretty quick - the new rules are very strict and they can loose their import rights if there is any suggestion that have done the wrong thing.

ie, you have "hand". use it :P

100% correct there. At best it's a fine and at worst, their license revoked/suspended.

Everyone seems to be ready for the worst from Nagoya, in my experience Alex is a very upfront guy.

There is very little warning of impending turbo doom on these cars, so I don't believe this is a case of someone flogging a dodgy car. It's annoying for sure, no one likes problems immediately after a substantial outlay, but don't go off half cocked.

Before you assume the worst, give him a call, be calm and explain the situation, I'd be very surprised if you need to threaten to achieve a satisfactory outcome. He does have a good rep with repairs and appears interested in keeping the good reputation he's worked for.

Good luck, Hope you get it sorted quickly. Dale

Yeah i've had good dealings with nagoya in the past too, mainly D'mitry. He's even given me advice that resulted in him getting a lower profit margin. Like Daleo says, give them a call and play nice to start with.

Give them a chance to handle it properly. If they seem hesitant, mention that replacement is required under the 3 month stat warranty.

If they decide to be a complete **** about it then tell them you'll take the complaint higher up and you'll feel obliged to mention the sub standard compliancing performed while your at it.

But as mentioned above, Nagoya seem to do a pretty good job of dealing fairly with their customers. Give them a chance to continue that.

I gave D'mitry a call again today and he seems pretty helpful so far. They will pay for the brake skim and torn right CV boot. Although in my opinion these two things should NOT have even gotten close to passing roadworthy.

In regards to the turbo, first he tried to steer me into the warranty that came with the car, but once I mentioned the 3 month statutory warranty he said he'll talk to the boss (who's been overseas in the time I've been dealing with Nagoya). But I was told to get quotes from two separate mechanics in the mean time.

However, he told me the tyres are fine and totally legal. Yes the tyres look brand new with 100% thread. But after reading more about compliancing I'm am lead to believe that this is irrelevant and they MUST be BRAND NEW AUSTRALIAN tyres. I double checked the tyres and they're Yokohama Ice Guard iG20, and does not have a DOT number, which would mean not ADR compliant? Or is there a different method used to indicate ADR tyres?

So at the moment it's looking ok. But I do agree with what Daleo and Messiah posted about them not knowing when the turbo would go, as it was fine before, then just gave up the ghost. So not their fault at all, just unlucky.

So far I've got very mixed feelings about Nagoya Motors. On the one hand they have been helpful on the phone and playing ball. But I must say I was NOT impressed when I picked up the car!! It was parked under a tree with bird crap all over it, there was a fresh banana peel on the passenger side floor, keyless remote battery was dead, had warped brakes, torn CV boot and non ADR tyres which both shouldn't have passed road worthy. In my opinion that's a pretty poor effort for a dealer...

Edited by Vesza

tyres are cheap, i have an almost brand new set of M35 RS/RX wheels and tyres here if you want them.

just get the important things fixed (turbo, brakes and CV boot) and worry about the small stuff later (tyres)

Not meaning to be a bastard... but you did get a full mech inspection before purchasing didnt you??

Nope, I didn't bother this time because I was going through a dealer. They run a business and are responsible for selling you a good product which has been complied and roadworthied properly. Where as when I buy from a private seller I always get a mechanical check because there is no warranty what so ever and they are not liable for anything. Again, turbo dieing is not their fault, but brakes, tyres and CV boot should have been checked by them.

tyres are cheap, i have an almost brand new set of M35 RS/RX wheels and tyres here if you want them.

just get the important things fixed (turbo, brakes and CV boot) and worry about the small stuff later (tyres)

Yeah true, tyres are the least of my problems at the moment and I will get that sorted after. However it's not really the point and I would estimate it to be around $80 for a cheap tyre (215/55/R17) so at best $320. I've also heard snow tyres are not suited for high speed (highway) use, on hot days. Apparently the softer compound turns to mush and is unsafe.

Edited by Vesza

Snow tyres are DEFINITELY not safe on hotter weather conditions. Not only does the tread blocks deform, but they can completely tear apart as well. I've seen it before. Another point to note as well. Snow tyres on cars can mean they are from a snow region. And generally (although not all cases) these cars will have some form of corrosion underneath.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
    • So my car is finally back from paint! This took an absolutely insane amount of work and should get it's own build thread - but I didn't build it. It was completed by Troy @ https://scalekustoms.com.au/ I originally bought the AOSHIMA URAS Type R kit while I was in Japan, it's supposed to look like this when assembled: Now, I thought that was cool enough until I opened the box with Dismay, as there's no way I could possibly have completed it. The thing is 1/24 and has details down to the steering wheel horn button, which is a 2mm diameter sticker. I originally wondered if someone could make it at all, as is - But then things got a little carried away. It's worth noting that the model does not have an openable bonne, let alone engine bay, OR an openable boot. - Troy has worked wonders with 3D printer and presumably better eyes than I will ever have. My photos suck, so I will post up some of his in-progress ones he sent to me during the way. Unsuprisingly, he is very detailed. A lot of these are out of order. But he: 1) Made a LS engine and an engine bay appear out of thin air 2) Made the bonnet removable 3) Printed the rims I will buy in the future (or any rim you want) 4) Printed and added the wing that is going on 5) Tinted my back windows as this is what my car has IRL (privacy glass) 6) Added a licence plate. 7) Somehow did the interior 8) 3D Printed my actual seats 9) Made the exhaust under the car connect even though this is likely invisible. 10) Created a boot with my fking battery box, power steering reservoir, subwoofer and toolboxes back there. To say it's insane is an understatement. And I f**ked it all up because when I was re-mounting the wing (it broke in transit) I spilled glue everywhere and ripped paint up and Gregged the rear half of the car. Which about makes sense. Also, this arrived on the same day. Quite the change from: I spent 16 hours per day over the next 3 days pre-christmas putting the interior back together, mounting lip, fixing various bodykit problems with window mouldings, etc. and servicing, rebuilding my 370z brakes to go on the car 'soon', messing with heights to check clearances for new wheels, etc. I also had a foray into mounting wiper-mounted washer jets which was an absolute disaster. The bodyshop has welded (and painted) over the stock jet locations for reasons unknown to everybody (i.e they forgot) I also wanted to wire in the oil pressure sensor on Christmas Eve which was a BAD IDEA. You do not know terror like pulling your ECU apart, pinning in half-fitting pins that aren't the right ones, but trying anyway because it's Christmas eve, putting your ECU back together and having a no-start condition with a fuel pump not priming. Then you undo all your work and the fuel pump still doesn't prime. So after all that terror and horror and pain and tedious disassembly, the issue was the relay in the boot which seems to have died/stuck when I was turning the car off and on about 700 times testing shitty washer jets. I also re-wired the fuel pump power plug which fell apart in my hands. I am very happy I had 3 extra pre-made ones from a few posts/last Christmas's breakdown. https://bluewireautomotive.com/products/10-x-pcm-ecm-ecu-terminals I have put an order for these in, so I can actually add the pins to the ECU properly. The commodore ECU does not have the pins for Oil Pressure via ODB2. However the ECU can support it if you create the pins and wire them in. So for round two, and somehow attempting to route that into the engine bay through my impossible engine bay grommet is a fight for another day. It's 40C in Melbourne tomorrow, I am half tempted to drive the car with the aircon on to deliver presents to my partner's family and see if it helps with the overheating-on-40C-days-in-traffic-with-aircon-on-only issue that the vents were intended to solve. Do I feel lucky?
×
×
  • Create New...