Jump to content
SAU Community

Recommended Posts

ok so here's the deal, i bought a car in Japland, R32 GTS-t, has a BNR32 Rb26 in it, and according to auction sheet, a T78 turbo, assuming a 33D going by what they sell. Now internals are unknown, but seeing as nothing was listed, im assuming stock.

My first question is, is there any possible reason i should keep the T78 if i dont plan on fully building the engine? it will be used mostly for drift, so heaps of power isnt really needed hugely, but also some time attack, so extra power would come in handy.

My 2nd is, what kind of turbo from Greddy's lineup would be more suited to my goals of say a reliable 300rwkw, that would fit on the kit these come with (exh. manifold etc)? i'm not a low down torque hunter, so im not interested in chasing that 100rpm of less lag. i just want something that will provide usable power without having to change everything else around.

cheers

Link to comment
https://www.sau.com.au/forums/topic/311305-t78-on-internally-standard-rb26/
Share on other sites

btw, mods:

Trust T78-33D

PowerFC w/Commander

HKS EVC4

Trust Manifold

Trust External Gate

Tomei Type-R Poncam

SARD Injectors

Adjustable type fuel regulator

HKS Pod Filters

Z32 twin AFM's

Trust Intercooler

Trust Oil Cooler

3-Layer Copper Radiator

Low temperature Thermostat

Turbo Back Exhaust

and before anyone asks, these are as detailed as they get for now, going off translated for sale ad.

it doesnt make sense, you say you want it for drift (small turbo) then you say you want not heaps of power (small turbo) then you say time attack (big turbo) then you say extra power come in handy (big turbo). which one do you want? it would seem odd to fit a T78 to a std engine, you certianly could do it, but why would you bother?

with bog stock everything you would be lucky to tune it at 12psi and not max everything out - aka pointless

wait till the car comes over and then check it out

if its got all the suppporting stuff on it, sell the T78 and get a mid sized hks GT28x/30x series and away you go, even a pair of GT-SS would be fine

but as its already in single mode, its probably cheaper to keep it in single mode

My 2nd is, what kind of turbo from Greddy's lineup would be more suited to my goals of say a reliable 300rwkw

honestly didnt think it would be that hard to decode roughly what power area i was aiming for lol

i have it here in Japan, unfortunately i dont have the time or tools to do much snooping around on it for a few weeks til im in Osaka where i will have access to some decent shops.

as i mentioned, i would prefer to keep with something that fits the current manifold to make it an easier job, i have nfi what will fit or not (whether it's a universal flange size that HKS shit will fit on etc), i just dont care enough about turbos to carry any knowledge about them haha

I'm assuming from you post that its not yet in your posession, hence the sort of speculative question? :)

Throw it on the road..... once you open it up you'll realise that you won't want to replace it with anything else :)

If insane horsepower isn't quite what you were looking for, you 'll pretty much need to go outside the TRUST stable of turbos to find something suitable. A GT35 would fit the bill in terms of reducing lag and providing similar power levels (though you could consider a GT30 the next size down if need be).

ahk so are we talking all new kit to switch tables to HKS gear?

i have the car here, have driven it etc, currently running about 0.8bar but that's mainly due to me having nfi how to get the EVC working lol

the other problem is not knowing it's current tune, or model/condition of fuel pump. it's quiet most of the time, only occasionally making a buzz, certainly nothing like what i'd expect from something of a suitable size, the 040 in my 4dr at home is always buzzing in the background of a noticeable noise level.

Pretty sure Greddy/Trust use a different type of flange than garrett/hks turbos on their manifolds.

If you want 300kw look at the Trust TD06-25g with 10cm rear housing or larger

http://www.trust-power.com/02turbo/turbo_charger.html

edit: found a photo of the design of the turbo; see different style flange

5b8f_10.JPG

Edited by Kaido_RR

RB26s beg for a big turbo, don't go down the TD route :)

Silent fuel pump dosen't nessicarily mean isn't a big one - have had dual in-tank pumps or single 044 which when mounted correctly are completely silent.

Your best bet is to get it your nearest Dyno & with all the appropriate gear and see how it goes..... you'll be able to touch up the tune / ensure fuel pressure is appropriate and then have all the fact to be able make a call on if you need to change the setup.

RB26s beg for a big turbo, don't go down the TD route :)

Silent fuel pump dosen't nessicarily mean isn't a big one - have had dual in-tank pumps or single 044 which when mounted correctly are completely silent.

Your best bet is to get it your nearest Dyno & with all the appropriate gear and see how it goes..... you'll be able to touch up the tune / ensure fuel pressure is appropriate and then have all the fact to be able make a call on if you need to change the setup.

i agree,

i don't see why they would be running a t78 with aftermarket injectors but stock pump.

RB26s beg for a big turbo, don't go down the TD route :)

Silent fuel pump dosen't nessicarily mean isn't a big one - have had dual in-tank pumps or single 044 which when mounted correctly are completely silent.

Your best bet is to get it your nearest Dyno & with all the appropriate gear and see how it goes..... you'll be able to touch up the tune / ensure fuel pressure is appropriate and then have all the fact to be able make a call on if you need to change the setup.

yeh definitely, unfortunately there is dick all in Nagano as far as car tuning goes so will have to wait for Osaka.

I agree, throw it on the dyno and see how it goes. If it makes good power on the dyno drive it for a while and see what you think. No point spending heaps of cash before you even know what you have.

Please dont get anything smaller than a GT35.

I think you mean 340-350rwkw not just 300 :)

t78 on a well set up GTR is one of my 1st choices. Drive it before you think about changing it. The fastest circuit car ive been in is the signal R34 with T88 and it was driven to and from the track and used daily.... it all comes down to setup.

I love my T88, T78 would be good as well.

Open her up on the highway, make sure its not missing and isn't hesitating when you're going WOT.

Also look out for boost creeping / spiking as well, but if you're only running 0.8 bar thats barely getting into the T78.

I'd just take it easy... stock fuel pump is very strange, it may have a sard intank, they are quiet as all hell and a very popular choice with the sort of setup you have.

To be honest i'd just take it easy until you get a dyno run and have a look at how the AFR's are going, also you mentioned you have a power FC with commander? give the car full boot and have a look at the Duty Cycle, you don't want to be going over 85%.

I love my T88, T78 would be good as well.

Open her up on the highway, make sure its not missing and isn't hesitating when you're going WOT.

Also look out for boost creeping / spiking as well, but if you're only running 0.8 bar thats barely getting into the T78.

I'd just take it easy... stock fuel pump is very strange, it may have a sard intank, they are quiet as all hell and a very popular choice with the sort of setup you have.

To be honest i'd just take it easy until you get a dyno run and have a look at how the AFR's are going, also you mentioned you have a power FC with commander? give the car full boot and have a look at the Duty Cycle, you don't want to be going over 85%.

slight hesitation sometimes when it gets to around 6k, but generally pretty smooth. inj duty cycle averages around 75% before i back off, yet to see it break into the 80's

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No. The ECU's hose is for a connetcion between the plenum (assuming single throttle body, not ITBs) and the ECU's internal MAP sensor. This is the primary load measurement of the ECU - so you need to get this one right. This has NOTHING to do with the boost contol. The wastegate also needs to see a boost signal - but it is actually far better for it NOT TO COME FROM THE PLENUM (again, assuming single TB, and not ITBs). This should come from the turbo's compressor housing (assuming there is a nipple on there, which there might well not be), or on the boost pipe somewhere between the turbo and the TB. On the pipe from the turbo to the intercooler is usually most convenient. The boost controller is then located between that boost source and the wastegate, ACCORDING TO THE CORRECT PLUMBING DRAWING FOR THAT BOOST CONTROLLER. There is no general diagram or instruction that will be correct for every case. Then the other ports on the plenum are for purposes such as Duncan described. If the boost controller has an internal MAP sensor, for a boost display, etc, then it will want to be hooked up there, alongside the ECU and the FPR.
    • Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
    • From there, it was just a quick electrical check, prime the oil and start her up Which, is not what happened. 1. Bloody seppo Aeropro battery holder. Not only was it too tall for the battery (which I'll forgive them for, I have another battery the same nominal size that is taller than Neil's one, but the bracket is a fixed height so the battery was spaced up) But the thing that really shits me is the hardware to hold it on requires a 7/32 Hex key. WTF. No-one will ever be able to remove or install the damn thing without a hex key they don't own 2. Kill switch no longer worked once the console was installed. Neil mentioned above he had to adjust the length but it no longer cleared the console once installed. Sorted. 3. Suspiciously, the brake light holders were hanging in the boot with no globes. Sure enough the stopper on the brake pedal was missing so they are always on unless the kill switch is activated. Will pick one up tomorrow (turns out 32 and 33 don't use the same stopper) 4. All that sorted, I turned on the kill switch, turned the key to ACC. Nothing. Turned it to IGN. Nothing. Checked some fuses and found the main IGN in the boot was missing which improved things once it was replaced. Now ECU and dash lights turn on with IGN but still no fuel pump. 5. Turned it to Start....ECU on, no fuel pump, no starter. Plus the voltage dropped straight to 9v.  I suspect the starter is f**ked but am going to have to work through it all and see what is happening, really looks like more than one issue. Does anyone have the R33 fuse box key with the circuit it sources from (eg BAT, ACC, IGN, SRT etc) and supplies? I can find a translated list showing Amps and circuit without supply circuit, and I can find supply circuit without Amps and target circuit.
    • 3rd time lucky, the AAC is now all plumbed up after getting some final fittings All set up under the plenum of maximum access
×
×
  • Create New...