Jump to content
SAU Community

Recommended Posts

Hey guys

i have a GTR R32 that's sitting in my workshop and taking up room..

Im happy to sell the whole thing as it is or even sell parts

call datto

0433780750

or workshop

03 9364 8898

thanks

Edited by swoooosh

hey mate,

Do you have the front guards and how much if you do?

Thx

Amon

  swoooosh said:
Hey guys

i have a GTR R32 that's sitting in my workshop and taking up room..

Im happy to sell the whole thing as it is or even sell parts

call datto

0433780750

or workshop

03 9364 8898

thanks

  jeffworld2 said:
Hi im interested in buying the whole car. What condition is it in and where are you located?

hey jef

i imported the car for my self, the company sent me misleading photos that let me down when the car came...

so i imported another gtr and used this car as parts, the best thing is to pop in and see it, im not sure on a price but im happy to talk more when you see it

i gave up on the car when i saw rust :P

still has the engine just bit's missing gear box and running gear still there, body parts are on it, it still looks like a car.. lol just bits missing

its a good part car, the car is in sunshine Melbourne

datto

  GTR 94 said:
is the car abs or non abs? also how much for the boot/fuel cable? i can pick up :P

hey guy's

I'v got a guy interested in the whole car for $5,000. if its not gone by the weekend ill be pulling parts off..

so guys start locking in the parts you want... i need this car out of my workshop asap.

thanks datto

for more info just call workshop or me

  SiR_RB said:
where ya located?

does it have aftermarket suspension? let me know if it does...

thanks

SUNSHINE!!!!! dude

i might have some aftermarket suspension around, ill let you know tomorrow.

Interested in the whole car, Can the car be street registered / Has it been complied?

Where is the rust - rear wheel arches, front sills/rocker panel etc?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...