Jump to content
SAU Community

Recommended Posts

hello every one.I have recently discovered that my stoko turbo has shat an oil seal.I am in the process of removing it and i have all intercooler piping out of the way.

I need help with the following

-where do i disconnect the dump pipe at the turbo or where it bolts onto the main exhaust (300mm away from turbo)

-what is the best method for removing the oil and water lines how do i get to the rear oil or water line right next to the exhaust manifold

-do i remove the exhaust manifold or just unbolt turbo from it

-when i pull water and oil lines off will i need to plug them up or will they not leak

-Are there any gaskets i need

-Any other information that may help me with the removal and installation of new turbo

Thanks in advance for anyone contributing any info,as you could probably tell i am planning to get the job done myself and have decided removing and rebuilding and high flowing original turbo,i know lots of people will disagree and suggest putting monster turbos and manifolds on but unfortunately this is the budget i am on, and have heard positive info from some reliable turbo re builders in bris.

I did this recently myself, bolting up my new turbo :D

where do i disconnect the dump pipe at the turbo or where it bolts onto the main exhaust (300mm away from turbo)

Unbolt it at the rear of the turbo, where the dump pipe bolts on.

what is the best method for removing the oil and water lines how do i get to the rear oil or water line right next to the exhaust manifold

I just used a 24mm (I think) spanner. It's FAR easier to get at it from beneath the car, get it on a hoist if you can. As for the other lines, they just unbolt.

do i remove the exhaust manifold or just unbolt turbo from it

Just unbolt the turbo from the exhaust manifold. There are four bolts, I think they're 17mm from memory.

when i pull water and oil lines off will i need to plug them up or will they not leak

They will leak, but don't worry about plugging them up unless you're worried about making a mess. Just top up afterwards.

Are there any gaskets i need

You may have one between the turbo and the dump pipe. The one between the turbo and the exhaust manifold should be OK to reuse. If the top oil feed on your turbo has the two-bolt connection and you undo it (you don't need to) then you'll need another gasket in there. It's advisable to replace the nylon bushes around each of the fittings into the turbo too.

Any other information that may help me with the removal and installation of new turbo

You should be able to find a bit more info in my other thread: http://www.skylinesaustralia.com/forums/sh...ead.php?t=30556

You'll have a fair bit of trouble finding someone who stocks gaskets - Nissan doesn't list anything, Holden only list a flange gasket. Repco/Autobarn/Walkers don't have listings for them at all.

What I ended up doing was getting some asbestos extractor gasket material and cutting my own gaskets, but I believe this is illegal to sell as of new years', so you may have to resort to gasket goo.

qik, see you at Drag Combat :D

nissan have everything for any skyline , u have to go to a dealer that deals with imports , not all of them do .

there are several dealers in sydney that do though .

shoe dgo to hornsby nissan they will help u , if they dont have in autralia they will order from japan about 1-2 weeks ( no charge for freight either .

if u r closer to parramatta go there but their spare parts is in rosehill .

turbo is off now took me 1 1/2 hrs gasket from turbo to dump pipe in good condition.The head was off the car about 5 months ago so most studs and gaskets are fresh.The only prob i had was unbolting water line that sits between turbo and engine but i left it till last as it was hard to get to and slightly kinked it but its fixed now.The turbo is now at Turbo Torque (used them before on my vl turbo and they were very affordable and dont add on extra costs ).Hopefully have it back in a week and then bolt it up and off we go.

Does anyone know if there is an air bleed screw in the cooling system on r33's.

Also is there a process to bolting back on that involves priming oil into turbo or any thing little that needs doing prior to starting the engine.

thanks again

just spoke to rob at turbo torque .The turbo will be highflowed both compressor to t3 and exhaust.The skyline turbo is non repairable so he is using parts off a vlk turbo then high flowing to t03/t04 for $1450.

the new turbo will give 20-25% hp increase.

Just for intrest brisbane turbo and tuning quote 2100

Just incase you haven't found any gaskets yet, you can get them from GCG in sydney. They have a 3 gasket kit for 40 bucks that includes the t3 flange gasket, dump gasket and oil drain gasket.

They do mail order stuff too i think

If you got it off then you shouldn't have problems getting it back on.

The only problem i had was the core was rotated very slightly, less then a degree, which made it a bit difficult to get the banjo bolts started. Other than that it was a piece of cake

sorry for jacking the thread qikr33 have you fitted on ur turbo back yet?

cause Im also about to attempt to bolt on a turbo back exhaust

Are there any more gaskets on the exhaust besides the one between the dump and the turbo?

am I right to assume that the you need to replace that gasket once you remove the stock dump pipe?

sorry lukits havnt bolted back on yet will do it on friday so i am not sure what gaskets i nedd.There is a steel gasket that i removed between turbo and dump pipe and i can surely re use this one as for the seal between turbo and manifold i cant remember but i will have a look for you and post again a little later.

well its been almost a week and a half and i got the turbo back(will post pics soon).It all bolted together,i found that where it bolts onto exhaust manifold it had a steel gasket so i re-used it with some manifold cement as assurance of a good seal.The sam went for where it bolts onto exhaust manifold it also had a steel gasket.

Only dramas were finding new copper washers for the banjo bolts...only place i found that had them was lewis hoses (slacks creek near moss st) cost me $3

before i started the car i pulled the fuel pump fuse from the boot and cranked the engine over for about 30 sec to get the oil up to the turbo(as it said to do with the card that came with it.)Took it for a drive and it takes a few revs to spool this baby up but then when it hits 10 psi it really has some get up.I need a new bov as the stoko one isnt letting enough air out now between changes and sometimes you get a fluttering noise.Started raining so i couldnt put the boost up any more but will be as soon as it stops but definitly more lag and hopefully more power.

i will post more stats up when i get a chance to thrash it a bit more. :wassup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • H2 (for cars) will never happen. It's not reasonable for any number of reasons. It's also not reasonable for almost all of the industrial uses that the fanbois say that it will be used for, again for a large number of reasons. There are some cases where it will be good. But, even those will be massively hampered by the economics. The only way that H2 can be economic is if we somehow manage to get from where we are to the other side of the economic-valley-of-death in which no-one can operate. You need there to be sufficient renewable generated electricity to be available so that it is effectively free. Once you are there, you can do whatever the hell you want and hang the efficiency. But until you get there, the ever diminishing value of electricity makes it harder and harder to encourage businesses to build the new generation capacity, and they will simply stop investing in generation projects. (I kinda think there needs to be just government money spent on building the required capacity in a non-commercial way, similar to how the first fossil fueled grids were built, as national-government owned utilities. And probably some nuclear in there to start. But this all should have started 10-15 years ago to avoid the chasm of death that we face right now). Synth fuels will be much more likely, but will only occur is there is at least some renewable H2 production, because you need H2 to do it. And you need stacks of free (or at least extraordinarily cheap) energy because assembling molecules back into fuels is exactly the opposite process to burning the fuel, and the reason we burn fuels is because there is so much energy squeezed into each molecule. So you're somewhat subject to the same economic valley of death problem as above anyway. That is unless people are willing to pay the current equivalent of $5 or $6 per litre of petrol-ish liquid fuels. Can you imagine it? The squealing at $2 now is bad enough.
    • This is so cool. Get a dashcam that records audio and hopefully you'll catch it.  Maybe there's a brand or some kind of markings on the back ? Are the pics hand drawn? I love it so much.
    • Hahaha yep, point(s) taken. I just like seeing different things and an EV in an R32 is pretty different. I'm not on the EV band wagon, I'm waiting for synthetic fuels or hydrogen personally. 
    • I mean it's probably likely that people overestimate their skills in dialling in a setup and noticing the changes. I had SK shocks and springs, and added heavier springs and got them revalved by Sydney Shocks to suit based upon what I told them I wanted the car to handle like. I got back a completely different feeling set of shocks, which probably (?) feel great on track but holy hell are they rough on tram tracks and the like. The shock dyno actually looks pretty similar to Shockworks (from what I can surmise from a screenshot of a youtube video - and my dyno printout...) Truth be told I doubt I'd be any faster or slower with either setup, or camber/castor combination. I also had whiteline eccentric castor bushes up front of my R34. I removed them and put in poly non-adjustable ones to soothe my OCD (nobody ever set the castor the same side to side, and it'd be near impossible to do) and be happy the wheel is centered in the well now for clearance reasons. Yes I wanted it to move 1mm 'back' :p I've effectively set my castor back to stock, negating all the benefits of that which is supposedly massive. I've probably also altered toe and camber in a negative (detrimental) way. I can't tell any difference steering the car.
×
×
  • Create New...