Jump to content
SAU Community

Fs: Used Exedy Nc10t Pressure Plate For Push Gt-r Or Gts-t // Machined (matte) Rb25det Flywheel // R33 Gts-t Or R32 Gt-r Push Slave Cylinder


Recommended Posts

Hi Guys!

Recently replaced my clutch kit so these parts are for sale!

Item: R33 1998 GTS-t Slave Cylinder

Condition: Good Condition, No Leaks, No Cracks on Leather Boot, 101k kms

Price: $40

Item: Exedy (NC10T) Pressure Plate from R32 GT-R Push Type Sports Ceramic Clutch (Silver One/Made in Japan/Not that Pink Shet :blink: )

Condition: Used, some very slight heat stress marks, came off my GTS-t.

  • Suits NSK-7121SO or NSK-7121SC
  • Pressure Plate Clamp Rating: 10,800N/1,101kgf,2,482lbf
  • Casting Type: Ductile (Anti-Burst) Cast Iron
  • Great for rebuilds!
  • Send it to Jim Berry

Price: $100

Item: R33 1998 GTS-t Stock Fly Wheel

Condition: Will Supply Machined with matte finish as recommended by Exedy

Price: $100 (Machined) $50 (As-Is, still very flat with no scores)

PICK-UP ONLY (Except Slave, will post for $8.95)

Location: Liverpool, NSW

Contacts: PM or Here!

Cheers,

Johnny

Clutch Slave SOLD

Available:

Exedy Pressure Plate

RB25DET Flywheel

RB25DET Pivot Point, will fit R32 GT-R Pre 1993

  • 2 weeks later...

Still for Sale! - Take the Lot for $120

** Exedy NC-10T Pressure Plate

** Factory Pivot

** Factory Flywheel un-machined

  • 4 weeks later...
  • 2 weeks later...
  • 3 weeks later...

TAKE THE LOT REMAINING FOR $100

** Fly wheel

** NC10T Pressure Plate

** Stock Pivot

  • 2 weeks later...
TAKE THE LOT REMAINING FOR $100

** Fly wheel

** NC10T Pressure Plate

** Stock Pivot

Is it still for sale ?

Could you put pics about pressure plate ? Can i fit it on my r32 gtr 1991 ?

regards

Is it still for sale ?

Could you put pics about pressure plate ? Can i fit it on my r32 gtr 1991 ?

regards

Hi there,

I will take photos of it on the weekend... Provided your R32 GT-R uses a 'Push-Type' clutch setup, then yes. I believe all R32 GT-R Pre March 1993 uses Push. Please check.

Hi there,

I will take photos of it on the weekend... Provided your R32 GT-R uses a 'Push-Type' clutch setup, then yes. I believe all R32 GT-R Pre March 1993 uses Push. Please check.

yes it's push type.... is it in good condition ? could i make paypal transfer ? could you send me it ?

  • 1 month later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
    • Oh yeah, always always always turn over an engine by hand first.
    • So by that logic, an insanely expensive GTR for $200k+ is quite cheap, at 12% of Sydney's median house price compared to over 50% when a GTR was new...
    • Apologies... thought i had outlined it... Cheers for the response, I'll get a nipple sorted out for this.
    • lol thanks for the pics but some arrows might have helped for context. If you mean the bit I've badly traced in red, that is a PITA vacuum signal for the power steering pump, only R34 GTT was "lucky" enough to get it. Yes you will need a nipple of the same size somewhere in the intake between the air filter and the throttle or the power steering idle up will not work correctly
×
×
  • Create New...