Jump to content
SAU Community

R34 Rb25det To Rb30 Conversion

SKYLINE SAMOA
 Share

Recommended Posts

urtwhistle Proficient

urtwhistle

Posted
Posted

My Bonnet wont shut damn it!!!!!! the R34 bonnet height must be slightly different to the R33 When using a stock manifold as it is hitting on the BOV flange. I redrilled the engine mounts as per the manual but it still isn't quite low enough. It just gets on the 1st click of the bonnet latch, So I will try washers on the bonnet hinge and or chop the top lip off the BOV flange and re tap a bolt in lower.

I'll let you know what I do to get around the height problem, but a Greddy plenum would have been the easiest solution while the motor is out.

Chris

bubba Grand Master

bubba

Posted
Posted
My Bonnet wont shut damn it!!!!!! the R34 bonnet height must be slightly different to the R33 When using a stock manifold as it is hitting on the BOV flange. I redrilled the engine mounts as per the manual but it still isn't quite low enough. It just gets on the 1st click of the bonnet latch, So I will try washers on the bonnet hinge and or chop the top lip off the BOV flange and re tap a bolt in lower.

I'll let you know what I do to get around the height problem, but a Greddy plenum would have been the easiest solution while the motor is out.

Chris

Did you slot the engine mounts?

Are you still using T/C? if not, I can give you an RB20 crossover pipe to try, it mounts teh bov in a different orientation.

Mine only hit on the lip of the timing belt cover and forward corner of the intake manifold.

Let me know if you want me to come take a look Chris :thumbsup:

urtwhistle Proficient

urtwhistle

Posted
Posted
Did you slot the engine mounts?

Are you still using T/C? if not, I can give you an RB20 crossover pipe to try, it mounts teh bov in a different orientation.

Mine only hit on the lip of the timing belt cover and forward corner of the intake manifold.

Let me know if you want me to come take a look Chris :woot:

Hey Bubba, cheers for the offer I may take you up on that at a later point.

Yes I slotted and rewelded the engine mounts to the max. I'm still using the T/C throttle body but it has no butterfly fitted. It didn't end up hitting the throttle body it self but the rubber sleeve between the throttle body and the cast aluminum pipe that the BOV mounts to.

what I ended up doing is cutting a small slot out of the bonnet to clear the joiner/throttle body. Then took a ball peen hammer to the crappy Just jap IC pipe that runs accross the radiator. as it was clashing with the CAS sensor. the piping looks like crap but its good enough to get the car running on and i'll get a replacement bent up later as i have well and truly used up all the goodwill with borrowing my mothers car.

A simpler fix would have been to use a R33 throttle body and get a pipe bent up to replace the cast ally peice.

regards

chris

bubba Grand Master

bubba

Posted
Posted
Hey Bubba, cheers for the offer I may take you up on that at a later point.

Yes I slotted and rewelded the engine mounts to the max. I'm still using the T/C throttle body but it has no butterfly fitted. It didn't end up hitting the throttle body it self but the rubber sleeve between the throttle body and the cast aluminum pipe that the BOV mounts to.

what I ended up doing is cutting a small slot out of the bonnet to clear the joiner/throttle body. Then took a ball peen hammer to the crappy Just jap IC pipe that runs accross the radiator. as it was clashing with the CAS sensor. the piping looks like crap but its good enough to get the car running on and i'll get a replacement bent up later as i have well and truly used up all the goodwill with borrowing my mothers car.

A simpler fix would have been to use a R33 throttle body and get a pipe bent up to replace the cast ally peice.

regards

chris

Nice work, but the most important question is, skids?:)

I have to find some time to duck up to the workshop and pull my pistons out, then I can send everything to the machinist!

urtwhistle Proficient

urtwhistle

Posted
Posted
Nice work, but the most important question is, skids? :)

I have to find some time to duck up to the workshop and pull my pistons out, then I can send everything to the machinist!

Not yet mate, 36k's on the clock and its painfull I just wanna give it some Revs damn it. It's booked in for a quick run in tune on tuesday then I wont have to fear about leaning it over 3-4krpm.

Josh DO IT, it has so much torque every where compared to the Rb25 with a hiflow. I mean 3rd gear 2krpm from walking pace tractored straight up a damn steep hill.

chris

bubba Grand Master

bubba

Posted
Posted
Not yet mate, 36k's on the clock and its painfull I just wanna give it some Revs damn it. It's booked in for a quick run in tune on tuesday then I wont have to fear about leaning it over 3-4krpm.

Josh DO IT, it has so much torque every where compared to the Rb25 with a hiflow. I mean 3rd gear 2krpm from walking pace tractored straight up a damn steep hill.

chris

Ugh run is so painful hehe

Shoot me a PM when you're ready for skidz and I'll bring the vidcam down :D

  • 1 month later...
Redliner007 Enthusiast

Redliner007

Posted
Posted
Hey Bubba, cheers for the offer I may take you up on that at a later point.

Yes I slotted and rewelded the engine mounts to the max. I'm still using the T/C throttle body but it has no butterfly fitted. It didn't end up hitting the throttle body it self but the rubber sleeve between the throttle body and the cast aluminum pipe that the BOV mounts to.

what I ended up doing is cutting a small slot out of the bonnet to clear the joiner/throttle body. Then took a ball peen hammer to the crappy Just jap IC pipe that runs accross the radiator. as it was clashing with the CAS sensor. the piping looks like crap but its good enough to get the car running on and i'll get a replacement bent up later as i have well and truly used up all the goodwill with borrowing my mothers car.

A simpler fix would have been to use a R33 throttle body and get a pipe bent up to replace the cast ally peice.

regards

chris

So if im using the r32 rb25de head with standard throttle body and piping It should prevent the fouling on the bonnet if i get the mounts to sit as low as possible? Im not too keen to go front facing if i don't have to.

urtwhistle Proficient

urtwhistle

Posted
Posted
So if im using the r32 rb25de head with standard throttle body and piping It should prevent the fouling on the bonnet if i get the mounts to sit as low as possible? Im not too keen to go front facing if i don't have to.

just remove the nice cover off the bonnet put a big dollop of grease along your throttle body to BOV. drop the bonnet down see were its got grease. pull out trusty 5" angle grinder and remove the small peice of bracing. bonnet sorted. But you still need to drop the motor to the absolute max, and for good measure i put 2 washers under the bonnet hinge and lifted the bonnet latch a few MM.

Redliner007 Enthusiast

Redliner007

Posted
Posted

and chuck the cover back on? Im just concerned as I'm planning on getting the car all certified for the streets afterwards and don't want it to effect that. How is your conversion coming along anyway?

urtwhistle Proficient

urtwhistle

Posted
Posted

yeah mate, just spray some primer over the raw edges and then put the cover back on. what you can't see aint gonna hurt them mate. its not like you have removed all the bracing . just 100x100mm square.

My cars running and tuned done 2000k's, made 366hp 500nm @ 5500rpm. needs a little more boost and she will be sweet.

Redliner007 Enthusiast

Redliner007

Posted
Posted

Nice mate!!! Is this in your r34? You got any pictures of how she's sitting in there? I can't wait to start my conversion aye, just need to get rid of my r33 first get pay off some bills before i get into it lol.

366 5000nm thats nice man bet it pulls hard. What turbo and boost are you running urtwhistle?

Redliner007 Enthusiast

Redliner007

Posted
Posted
I'll have to take some pics, the turbo is a hypergear 3576. running 16psi. it doesn't make massive power but its mega fun to drive.

366hp still a decent amount for the street tho :happy: I bet it is a lot of fun!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      I just got to work and skimmed through 61508 and 61511. I was surprised the CSA adopted both, but neither are enforced. To recap what I read, it states that in a perfect world, they should be segregated but they acknowledge that this is not industry standard and clearly mention that they allow mixing of safety and non-safety. 61511 also mentions software segregation like AB does in their safety PLC's.   Now if only I could go back to control, let alone safety over comms. In my current line of work, we're only allowed monitoring and basic control over comms. Everything critical must still be hard wired as much as possible. 
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      I've unfortunately never been as they're on the complete other side of the continent and another country that isn't currently letting us in as easily as they use to. I even heard their stop signs over there actually say "Stop" instead of "Arret". If I decided to trek the 48h drive, I wouldn't know when or where to stop haha. Whenever I order parts from UP Garage, I order from Japan as it's cheaper. Same with GKTech... oddly enough, it's cheaper shipped from Australia then it is the US.  UP Garage Japan operates their US leg though, unlike Tomei. If Tomei JPN had the power to close down Tomei USA, I'm sure it would be done in a day. They're two completely separate entities. Tomei JPN messed up somewhere originally agreeing to its creation and got sacked big time. 
    • KKaplumbaa
      SR20 to cefiro

      By KKaplumbaa · Posted

      I asked someone about this and he told me about the Audi 1.8T engine. But I think it would be difficult to swap
    • MBS206
      The Cool Tools Thread

      By MBS206 · Posted

      I don't know that machine specifically, but I'd personally go for something with a little more kick than 130amp. Around up to 180 would be good. At the 6mm range, you're really pushing the machine hard and don't have a long period you can run for with out needing to give it a rest. Lots of MIG machines come with a regulator and hose. A lot will come with a starter roll of wire too, but it isn't too expensive to buy. I'd recommend NOT buying a massive roll too, as you don't want it sitting around FOREVER in the machine between uses and potentially going to shit. For thin sheet metal, get a roll of 0.6mm if you're doing over 3mm and above, switch over to 0.8mm wire. Even by 2mm you'd probably really want to switch. As for gas battle, it's all swap and go style now. You'll pay a bottle deposit, and then X amount to swap for a full one. I think it's like $200 or $300 for a D Size bottle upfront as "deposit", and like $110 to $150 per swap. My D size CO2/argon bottle lasts a fair bit of welding on the MIG. And I run an E size bottle on the TIG. For DIY MIG, stick with a D size bottle. If you really start to get into a LOT of welding and doing it really regularly, then upgrade. If you're like most DIY car guys, one D bottle will last you 2 or 3 years easily. I think I've been on my current bottle about 5 years. It is starting to get low, but I've been smashing it a lot more the last 6 months.
    • KKaplumbaa
      SR20 to cefiro

      By KKaplumbaa · Posted

      SR20s came with cars like the Bluebird and Primera, but the RB20 never came. The ones in Turkey were either brought in specially or from abroad. That's why RBs aren't as common as SRs. And if a part breaks or I need to replace it when doing maintenance, it's harder to find parts for RBs.
×
×
  • Create New...