Jump to content
SAU Community

Recommended Posts

looking at a car at imperial imports QLD, i have not herd of these guys, have you? any comments?

the original dash has 20ks on the clock, yes i know that is very, very low, definately worth a look i say.

anyway my question is the old (light) rust profing on the bottom of the car, its light not thick enough so you cant see under it, should i be alarmed? is it there to cover rust or damage? in what area of the car does it get its first cancer? where should i look?

i will thourougly inspect the car any way, what are your thoughts/advice?

post-32630-1269074498_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/312643-inspecting-a-20000k-r33-gtr/
Share on other sites

Looks the same as my old boat, but better, check around the struts, also the inner guards and under the body kit, where you find rocks and sand in Australia you find salt in Japan, put it on a hoist and have a good look around the diff and inside the boot under the spare and in the inner guards, a torch and a small mirror for looking in the dark and confined areas will be needed.

Hope its a good one

these days i buy cars based on how they run rather than km on the dash. the closer to 170psi compression and lower % leakdown is relative to the amount id pay. obviously you look for rust and excessive welding around the struts and in the boot as well as amount of play the suspension has. also the super helpful kick of the tires helps to check if the steering is loose.

don't pay a premium price for it if it isn't in premium condition, and if you have any doubts of it only having 20k on it then assume your gut instinct is right.

Its possible it is genuwine, but in reality it is very unlikely. Basically it should be in almost new condition inside and out, mechanical wise should be quitest r33 around.

Ignore the milage while you test drive it, km are irrelevant if everything is going well. And lets face it, it's and r33 gtr, not a Mclaren F1 or an F40 that are renowned for having low km's because they are more of a collectors car than an actual car you drive around in often.

Hope it is as good as the km's suggest it should be

i checked this car out today, so

the car drove like new, but not 20k new, maybe 70k or so (my guess)

it did have original exhaust, and untouched exhaust bolts! first time i see that.

the gut feeling was at at 50% not enough..

when runing my finger over the blue complience plate (a few times just to be sure) on two of he's gtr, they were not completely smooth, the were engraved!!

what do you think boys? clear as day??

when runing my finger over the blue complience plate (a few times just to be sure) on two of he's gtr, they were not completely smooth, the were engraved!!

Is that the blue plate attached to the fire wall? The compliance plate is usually a pink sticker on the strut tower.

If theres any chance that its a rebirth I'd walk away... but its unlikely a RAW would be selling rebirthed cars. Do some research on the company before buying from them though.

Is it the car listed on the Imperial Imports website with 22,567k's? Theres something on the coil pack cover that says 2.6 24 and then Nismo. It appears to have a few Nismo options, such as the steering wheel. It does look like a very clean car.

Edit: Steering wheel is Momo, not Nismo.

Edited by Priestley

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's the thing. Especially at idle, changing the cam angle by that much could be spewing more fuel out the exhaust courtesy of everything happening that bit later. More fuel also means more air (if the fuel didn't burn, then neither did the O2) and so the O2 sensors can start to tell interesting but misleading stories. And the specifics of what is happening could easily be affected by everything else you changed as well. And it could be dynamic, where a few revs more or less could somewhat change how the engine is breathing.
    • Good idea on the temp probe. The mv readings of the O2 sensors are very similar to one another, as is the injector pw. I went through logs in the past to see if there was a discrepancy and there is. Because they alternate up and down as narrowbands do.. they do often 'switch' as to which one is more. They were never 20%+ (more like 1-2%) so it's possible the difference between 20 and 15-17% is a similar discrepancy to 2.0% and 1.7% which I wouldn't have really noticed in the past. We did think about spacing the strut brace. Unfortunately the ~20mm that the GTR brace is lower than the GTT brace is effectively what you need to clear the vents. Moving it up would make it very uncomfortable, but it's plausible that 10mm is a unhappy medium between both hard places... The good news is.. using MR HAMMER it was actually pretty easy to bend back the bent bits to make sure the guard and headlight/new headlight tabs line up right. Yes, we used a R34 GTR guard to make sure the bolt holes all lined up with a known straight guard. As above, you can see the side skirt and the GTR guard are not meant to play together, but everyone seems to think this is a simple fix to the point where nobody who has had these talk to one another mentions how... ...so I'll just assume they know how to fix it when it comes to paint jail time again. Whoever they are. Nobody returns my calls. There's so much changed with regard to the ECU and the car.. that the next step really is to connect the scanner and attempt to drive the thing. It'll be pretty clear pretty fast how in or out everything actually is...
    • That's nasty! I think there is perhaps an inherent problem is using elastomers in such environments. The whole thing can and will get quite hot, and elastomers are not famous for their temperature resistance. On top of that, if the components are cast rubber or urethane and so on, there might be QA/QC problems with bubbles or voids in the material that could critically change their performance. They might just tear apart after being squished (presuming that any elastomers are used in compression rather than tension, I'm thinking that you squeeze one with a void in it and it tears the wall of the void to the outer edge of block, then the next time it extends or otherwise twists, it just gives up). This is all purely hypothetical, but it makes me wonder if the things that they have put into it to make it nice to use/live with are perhaps going to cause occasional failures like this. I wouldn't be getting up in arms over it, unless there are many repeats. I have personally ruined an Xtreme clutch - just an HD thing. I can't remember if it was still behind the 20 or was after the 25 went in. But it inverted some of the retaining spring/clip things around the outside. No-one could explain it. It wasn't thrashed, there wasn't heaps of torque being put through it, and there were no obvious problems other than the above. They were quite concerned by the event so they replaced it even though it was a few years old, which was very nice of them. As far as I am concerned, these things happen with clutches.
    • Any damage to the box/input shaft?
    • Hey there Mate , I just got my local guy to install it Waterhouse Performance, Penrith (specialise Nissan/Datsun and other performance cars) , you can do it yourself if you like , AMS has instructions on their website.  Cheers Pac
×
×
  • Create New...