Jump to content
SAU Community

Recommended Posts

looking at a car at imperial imports QLD, i have not herd of these guys, have you? any comments?

the original dash has 20ks on the clock, yes i know that is very, very low, definately worth a look i say.

anyway my question is the old (light) rust profing on the bottom of the car, its light not thick enough so you cant see under it, should i be alarmed? is it there to cover rust or damage? in what area of the car does it get its first cancer? where should i look?

i will thourougly inspect the car any way, what are your thoughts/advice?

post-32630-1269074498_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/312643-inspecting-a-20000k-r33-gtr/
Share on other sites

Looks the same as my old boat, but better, check around the struts, also the inner guards and under the body kit, where you find rocks and sand in Australia you find salt in Japan, put it on a hoist and have a good look around the diff and inside the boot under the spare and in the inner guards, a torch and a small mirror for looking in the dark and confined areas will be needed.

Hope its a good one

these days i buy cars based on how they run rather than km on the dash. the closer to 170psi compression and lower % leakdown is relative to the amount id pay. obviously you look for rust and excessive welding around the struts and in the boot as well as amount of play the suspension has. also the super helpful kick of the tires helps to check if the steering is loose.

don't pay a premium price for it if it isn't in premium condition, and if you have any doubts of it only having 20k on it then assume your gut instinct is right.

Its possible it is genuwine, but in reality it is very unlikely. Basically it should be in almost new condition inside and out, mechanical wise should be quitest r33 around.

Ignore the milage while you test drive it, km are irrelevant if everything is going well. And lets face it, it's and r33 gtr, not a Mclaren F1 or an F40 that are renowned for having low km's because they are more of a collectors car than an actual car you drive around in often.

Hope it is as good as the km's suggest it should be

i checked this car out today, so

the car drove like new, but not 20k new, maybe 70k or so (my guess)

it did have original exhaust, and untouched exhaust bolts! first time i see that.

the gut feeling was at at 50% not enough..

when runing my finger over the blue complience plate (a few times just to be sure) on two of he's gtr, they were not completely smooth, the were engraved!!

what do you think boys? clear as day??

when runing my finger over the blue complience plate (a few times just to be sure) on two of he's gtr, they were not completely smooth, the were engraved!!

Is that the blue plate attached to the fire wall? The compliance plate is usually a pink sticker on the strut tower.

If theres any chance that its a rebirth I'd walk away... but its unlikely a RAW would be selling rebirthed cars. Do some research on the company before buying from them though.

Is it the car listed on the Imperial Imports website with 22,567k's? Theres something on the coil pack cover that says 2.6 24 and then Nismo. It appears to have a few Nismo options, such as the steering wheel. It does look like a very clean car.

Edit: Steering wheel is Momo, not Nismo.

Edited by Priestley

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan! Yeah it's street use for me only. Maybe occasional track day. Any difference in noise when running with the two pumps? I would expect the lift pump to be more quiet than the main pump so hopefully not? And yes, unfortunately quite a big price difference to the simple hanger setup. Though I'm usually willing to trade money for better reliability and future-proofing. Buy once, cry once and all that. I'd be very happy to never have to deal with fuel pump / wiring issues again  
    • The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
×
×
  • Create New...