Jump to content
SAU Community

Recommended Posts

Not sure about the scrub radius... I lengthened the control arms by 25mm to get 2 1/2 degrees of Negative Camber, I guess it would have widened the track by about 60mm... normally you would want the rear track to be wider than the front, so ideally would swap the rear wheels to something with a deeper dish, but I won't bother...

Since the ball joint remains in the same location relative to the strut, wouldn't scrub radius remain the same???

I went 2 1/2 degrees because of the locked diff, 2 degrees would be plenty without that... it has helped enormously with turn in... At the same time I went to R31 Steering arms to quicken the rack up (effectively shortening the steering arms by about 12mm), so with the effect of that on the Ackerman, I can't be sure of what would have driven any change of feeling...

Instead of lengthening the control arms, the ideal would be using 240Z tops, and smaller springs, and relocating the bolt holes at the top, so you could get the Neg Camber without widening the track... but that is a lot more money than the car is worth...

I was going to use R31 Lower Control Arms so I could replace ball joints, but I would have needed to lengthen them by about 75mm, and there didn't seem to be an easy way to do that...

One day, I will probably get the caster rods machined up to be adjustable so I can adjust the caster...

Cheers,

Daewoo

well the scrub radius is the line from the top pivot point ie the strut top mount and the bottom pivot point ie bottom ball joint and where that line will meet the road compared to a line through the centre of the tire to the ground, this is to give you steering feel, if the top mount is standard and the bottom ball joint has moved out it will effect this, however it could be a good effect so thats why i ask? if you have plenty of road feel through the wheel it must be working well.

well the scrub radius is the line from the top pivot point ie the strut top mount and the bottom pivot point ie bottom ball joint and where that line will meet the road compared to a line through the centre of the tire to the ground

I think the scrub radius will be the same... The distance from the line through the ball joint to the strut top to the centre of the wheel is the same... to change the scrub radius you would need to change the line...

I think 240K/180B Steering arms have the ball join centered in the middle of the strut... R30/R31 Steering arms have the ball join set outwards in the strut... changing from a 240K to R31 Steering arm would change the scrub radius... but that offset is the same for R30/R31 that is swapped between...

Is that right???

Cheers,

Daewoo

  • 2 weeks later...

Just a bit of an update...

Our club is running our Wakefield Park Supersprint on June 20th. They won't let me run the white car because of the 'excess body damage' so I am going to try and get the green car ready... this is a car that has only been driven in the driveway since I bought it, so I have no idea what I am going to find...

I have disassembled and reassembled the gearbox with help from my mate Warwick... only ended up replacing a couple of bearings, and the front housings... didn't put the Zed first gear in, 'cause I decided it wasn't worth the hassle, and with a 4.8:1 diff, the gap between 1st and second gears is less apparent anyway...

I bought a ceramic button clutch for it, and have installed the clutch pedals, but that is about it... At the moment the car is on jackstands without lwer control arms, rear suspension, geabox, or diff

The list of things to do;

A Has to be done

B Should be done

C Would be nice

D If you have time

E Must be bored

A Buy & Fit Fire Extinguisher

A Fit 2nd Throttle Return Spring

A Fit Clutch and Gearbox

A Fit Diff

A Fit Lower Control Arms

A Wheel Alignment

A New Exhaust

A Fit Rear Suspension

A Fit front say bar

A Fit rear Say Bar

A Mount Battery

A Change Engine Oil

A Upgrade CAMS Licence

A Fit Air-box/Air Filter

A Clean/Vacuum car

A Swap tyres with Pulsar

B Weld up 4.8:1 Diff and fit

B Fit Shortened Steering Arms

B Side Exit - New Exhaust

B Bungs and plugs for removed pollution gear

B Fit Aftermarket Front Sway Bar

B Fit Aftermarket Rear Sway Bar

B Change Brake Fluid

B Fit Race Seats

B Swap steering wheel from White Car

C Fit Rear Wing to Roof

C Fit Cresida AFM and Airbox.

C Install Battery Cut-out switch

C Mount Battery In Car

C Get Harnesses back from Boob

C Fit Harnesses

D Lower Seat Mounts

D Remove Body Deadener

D Paint Bonnet

D Change Wiper Blades

D Rain-ex Fog-ex windows

E Paint Bottom half of car black and buy stickers

Cheers,

Daewoo

Hi Daewoo,

Just wondering... you've converted an auto to manual, does a manual R30 have the same ECU as an auto or are they different?

JH

Hope it is the same, or I am screwed - don't think I kept the ECU from the manual car I had before I sent it to the big scrapyard in the sky...

Hope it is the same, or I am screwed - don't think I kept the ECU from the manual car I had before I sent it to the big scrapyard in the sky...

hey daewoo

do any of your cars have grey interiors?

i need some door handles and door handle surrounds ?????

cheers

Hope it is the same, or I am screwed - don't think I kept the ECU from the manual car I had before I sent it to the big scrapyard in the sky...

Hopefully someone here will know for sure.

Also, I read somewhere that the auto flywheel is different to the manual. Didn't see flywheel in your list.

JH

hey daewoo

do any of your cars have grey interiors?

i need some door handles and door handle surrounds ?????

cheers

Sorry, both were brown...

Hopefully someone here will know for sure.

Also, I read somewhere that the auto flywheel is different to the manual. Didn't see flywheel in your list.

JH

Auto's have a flex plate that the torque converter bolts to... I have the flywheel from the car I pulled the gearbox from... needs a bit of a clean up, as it got a bit wet in the shed when I had it stored... but it will do...

Cheers,

Daewoo

how do you get into this stuff? barely looks legal haha

Neither car will be road registered... the locked diff and welded lower control arms put paid to that... the number plates are old ones that I never handed in... I just had them on the car when it was parked on the street to stop the council sticking a 'Tow Away' sticker on it...

The white car is barely legal for competition - I always check with the organiser that they will let me run without a grill and headlight... other than that it is OK, no sharp edges which is something they are always obsessed with...

The green car is a good car, and could be registered if I hadn't started doing mods that exclude it... but who wants to pay $1,000 per year for a car that is never driven on the road... you don't want to drive it to events, because you never know if you won't be able to drive it home :lol:

For $500 each, I reckon they are bargains... :) definately had more fun with them than the $30K Pulsar sitting in my mates chook shed...

Cheers,

Daewoo

Sounds like fun, As Wakey is only an hour a way i will come say gday...

maybe add perspex rear hatch to the list? have you felt how heavey they are!!!! i cant lift it on my own (almost)

my red parts car is about 1m in the air right now getting GUTTED. so I'll have a few years worth of spares.

the auto ecu will work with the manual, and so on. main differences between the 2 engines is the distributor. one has a different advance curve to the other.

also I have a 3 inch exhasut here you may be interested, its got surface rust, mild steel . but I wont be useing it as I have a 3 to 2.75 inch mandrel bent stainless system going on.

as I have a 3 to 2.75 inch mandrel bent stainless system going on.

Where you dig this up from?????

Though you might want to rethink this as I think a 3" system on your L24et will be detrimental to an 2" or 2.5". You have to have free flow in any turbo system and very nearly zero back pressure and restrictions, but 3", I don't know about?

Where you dig this up from?????

Though you might want to rethink this as I think a 3" system on your L24et will be detrimental to an 2" or 2.5". You have to have free flow in any turbo system and very nearly zero back pressure and restrictions, but 3", I don't know about?

The next Khanacross I was aiming for is the State round on May30th at Awaba near Toronto near Newcastle... but... I am also trying to get my other, undammaged MR30 ready for a Wakefield Park Supersprint on June 20th... so it very much depends how that is going whether I will go to Awaba...

I missed the first 2 rounds of the State Championship already (Overseas for the first, and had trailer problems for the second) so I am pretty much out of the running for the Champs, and I want to see how one of these will go on the track... They are good fun in a Khanacross, despite being fat and underpowered... if you get them singing they are good value...

Cheers,

Daewoo

  • 2 weeks later...

This knancross and what not is something I'm really keen to have a crack at one of these days, I have enough cars around the place I can use, I just always seem to be too busy. Building cars then fixing them all for mates none of my own cars.

Gonna have to look into it

Edited by DR JOSH

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
    • Yup but for me its the HR ! Cut my teeth on the old holden 6s in the day ! And here's me thinking in the day it was also the 300ZX and the Mitsubishi GT3000 ! All, as well had good lines, but always seemed to need finishing off, style wise.
×
×
  • Create New...