Jump to content
SAU Community

Wrecking R33

ang180

By ang180,
in Classifieds

 Share

Recommended Posts

ang180 Explorer

ang180

Posted
Posted

95 series 1 1/2 R33 complete interior parts no front or rear seats already sold.

R33 rear cradle no diff and breaks

R33 powersteering rack & hubs

R33 Bonnet

R33 series 2 Boot with Wing, rear bar & rear lights

R33 series 1 headlights excellent condition

S15 front 5 stud hubs with breaks off non turbo s15

R33 rear 5 stud hubs no breaks

Series 2 drivers seat no rips or tears

ALL MUST GO PM OR CALL FOR what u need and for PRICE OR MAKE OFFER

0433329781

Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/
Share on other sites
djnesnah Rookie

djnesnah

Posted
Posted
95 series 1 1/2 R33 complete interior parts no front or rear seats already sold.

R33 rear cradle no diff and breaks

R33 powersteering rack & hubs

R33 Bonnet

R33 series 2 Boot with Wing, rear bar & rear lights

R33 series 1 headlights excellent condition

S15 front 5 stud hubs with breaks off non turbo s15

R33 rear 5 stud hubs no breaks

Series 2 drivers seat no rips or tears

ALL MUST GO PM OR CALL FOR what u need and for PRICE OR MAKE OFFER

0433329781

Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/#findComment-5151072
Share on other sites
seriesII Mentor

seriesII

Posted
Posted
is that the bit thats rapped around the indicater stalk

its under that, its also is were the bonnet opening handle is, its a long colum, also there is a part there were you can move your steering wheel up and down. about 120cm, just guessing the length, but would be close.. ill find a pic if it helps a bit. im after one with no broken parts :banana:.. thanx

Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/#findComment-5151119
Share on other sites
ang180 Explorer

ang180

Posted
  • Author
Posted
its under that, its also is were the bonnet opening handle is, its a long colum, also there is a part there were you can move your steering wheel up and down. about 120cm, just guessing the length, but would be close.. ill find a pic if it helps a bit. im after one with no broken parts :thumbsup: .. thanx
is it the one where the fuse box is if so i sold it
Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/#findComment-5151786
Share on other sites
  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By TurboTapin · Posted

      Do the following first and get back to us. - Clean and verify your IACV - Verify for vacuum leaks/post MAF leaks. (Pressure test is the best and cheapest way) - Do you have a BOV with stock ecu/MAF? If so, remove it.     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      Hey all, The skyline I have is stalling when the engine is at normal operating temp.  When starting it while it is cold, it'll run just fine.  I have replaced the battery (bad cell), I have replaced the fuel pump, fuel filter and clean the MAF sensor.  Any other suggestions?
    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Thanks for all the information on this.  I tried ordering the parts from Amayama website and all 3 Solenoids are discontinued and not available.  Does anyone have any other websites to suggest that I could find the parts?   Separate issue-- I will start a new thread, but basically the vehicle is stalling when warmed up.
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      It's unfortunate what Tomei USA has done to Tomei's name in general. I'm very weary of ordering parts from them now. I only order direct from a Japanse source (e.g Nengun). At least their logos are different, so you end up knowing what you have. 
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
×
×
  • Create New...