Jump to content
SAU Community

"sa" R32 Gts-t Late 1993 S3 ,,nothing To Spend!

dato$2nv
 Share

Recommended Posts

dato$2nv Rising Star

dato$2nv

Posted
Posted

1993 r32 registered rb20det turbo , complied , registered , regency passed all the money spent to pass regency!!! hamburger with the lot lol

Imported from melbourne last year , regency defect after 2 days

over $4,000 spent on new suspension components , bushes , seals ect!! no leaks , no squeaks , no police hassels!!!

exterior...

Grey 2d coupe , rear spoiler has been removed and boot welded professionally , gtr rear pods , side skirts,., front bar gts-t with open mouth and faced edges looks like a bomex bar but better !!!! car has been resprayed recently , really good condition paint ,,, and then i reversed rear quater?(cracked bar and small dent) into something the next week!!! fat bad luck but will be fixed at my expense when i get the chance really busy with work!!!!

"""""Gold brand spankign new 100% tread work te37 18/235 they look awesome!!! these are worth 1750$$ on their own , i took off the stickers thinking they looked shit now i find out work is a good brand lol!!!!

Interior''

Nardi Torino steering wheel , little bit of flake but hey full drift spec.. short shift kit removed atm due to not wanting police attention comes with car,, boost gauge , good condition seats no rips or burns,, cd played , speakers , 12 inch sub and amp boot,,, small crack in cd surround probably 20$ for the whole surround

Engine""

Just serviced at 151,000 its at 152,500 atm!!!!

always serviced every 6-7000 kz with good oil and good filters

Rb20det twin cam , head has been done at some point has the red rocker covers but is the silver top 20det

*Huge fmic with alloy piping 3inch , looks awesome through the front bar

*3inch full Xforce exhaust , highflow Xforce cat , polished 5inch rocket tip , 3.5inch brass dump off turbo passed regency 91db , but i took of rear muffler i still have it but i estimate around 95 - 100dp now sounds killa,, gotta love rb20 idle bubble lol

*z32 afm with huge pod filter and cold air intake setup

*remapped computer by The speed lab , setup on dyno can map 17 psi but never has

*car also comes with uninstalled Greddy Emanage system with all looms vauled at 600$ brand new!!!!!

*rb25 highflowed turbo ,, can run 18 - 20 pound of boost aparently !!! would be saf at arounf 17 all day everyday

*single stage HDI boost controller i run 11 pound but has been at 1bar boost safely

*bosch 044 pump , 550cc injectors i think morpassi or bosch not sure tho,,,

*tomei adjustable cam gears , havent been adjusted much just a bit on the dyno again

*superspark coilpacks , platinum plugs

*brand new radiator cost $300 , brand new water pump $300

*dyno result ,, when i first got it it has a manual bleed and maxed out coils it was making 205rwkw at 1 bar , fuel pump was at 90%

*now with superspark coilpacks , electronic boot controller , 2 month old fuel pump $399 and boost lines set up to pick up fmic usually has extra lag running lines through carbon canister and not picking up ic pipes ,

!!!!!!!will make over 215rwkw safely at 15 psi !!!!!!!

With the emanage boost can be increased , fuel increased , cams dialled in more aggresively will make 230rwkw at 17.5psi with awesome cam timing!!!!!! and chuck in gtr or tomei cams and youll pull 250 - 280 rwkw

this car owes me huge amounts of money!!! but i will take """"$11.5k with the brand new rims and emanage and the dent fixed!!!

too be honest this car is very quick and has a lot of meaning to me , i need the money as i have 1900$ in legal fees due to some stuped incident!!!

Contact me via pm!!! or message / call me 0434008133

may consider swap for ute valued at under 5 grand + cash adjustement my way

post-46933-1269514296_thumb.jpg

post-46933-1269514325_thumb.jpg

post-46933-1269514497_thumb.jpg

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
×
×
  • Create New...