Jump to content
SAU Community

Recommended Posts

The 6266 would match the current power on some decent boost. But if u want to out power the T51r u may need to use a 7 series PT.

What are u going to use the car for? How laggy is it now?

Was planning to use it at the drags here in Tassie but looks like our track is closed down.

Its making 24 psi @ 5200 but my exhaust system was restricting it.

Which box is it exactly? I'd be more inclined to go a 6466 or 6766, if it's a power sucking C4 :) They are rated at 900/935hp.

I have the power sucking C4 :rolleyes:

if the 6262 goes 500 it must be the best turbo in the world, response of factory turbos and power of a large laggy heap of crap.....

I'd like to go up to Jez's dyno when my engine is done. Put it on there for 2 or 3 power runs then overlay it. From whats been shown so far, it could be big single time ;)

I'd like to go up to Jez's dyno when my engine is done. Put it on there for 2 or 3 power runs then overlay it. From whats been shown so far, it could be big single time ;)

FOR SCIIIEENNCEEEEEE!!!!!!!!!!

Sorry, couldnt hold it back. Now do it.

I am sure a 6262 could do that power on a DD, and that would not make it the best turbo in the world imho as there are others in similar territory. Here is an old example of what these turbos can do...

I woudn't look to AWD motorsport stuff to see what that would do(or any precision)..lol, unless you want to run no gate and

let the sucker make what it makes..lol, he did that on supraforums to a customers supra aswell,, 7675, making 7680 numbers.....and he did it to the record setting lancer in the video above , the thing apparently nuked itself not long after

I like his attitude and his balls though, haha

cheers

darren

Edited by jet_r31

I woudn't look to AWD motorsport stuff to see what that would do(or any precision)..lol, unless you want to run no gate and

let the sucker make what it makes..lol, he did that on supraforums to a customers supra aswell,, 7675, making 7680 numbers.....and he did it to the record setting lancer in the video above , the thing apparently nuked itself not long after

I like his attitude and his balls though, haha

cheers

darren

Of course that is kill mode, but that's serious business for a 62mm turbo without nitrous oxide

76mm compressor, garrett Gt42 S trim turbine(aka 4202), so sameish size as what you have( or same size as GTX4202), but if you have no

track i'd go smaller, be a toss up between a 6766 and a 7175 i reckon..

cheers

darren

Edited by jet_r31

PJ, what have you seen the 6262 and/or 6266 go to power wise?

Will the 6266 crack 500?

A 6266 will crack 500rwKw all day on an efficient engine. A mate of mines car made 491kW on a plain jane GT35 with .82 T3 housing, then went out and ran a trap speed of 147mph, 1400kg car including driver!!!

Yeah that sounds more like it Lithium, 900whp is a MASSIVE number given the size of the compressor and turbine wheels

My 6766 peaked at 853hp on Mainline at 42psi, running it any harder may have just caused drama's so we called it a day.

The yanks have gone very fast with these turbo's no doubt, they also have the cars setup to take an absolute pounding. I believe they have gone as quick as they have without any GST on the story, I still find it amazing how they are going 145+mph on FP Red's though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...