Jump to content
SAU Community

Recommended Posts

On 01/03/2018 at 12:20 PM, SimonR32 said:

Should be interesting on weekend at Racewars, have 1000m run and I'm guessing I'll pick up a lot of speed from the sequential box. Best guess is around the 295km/hr region 

Only got to 291km/hr but with the 30-40km/hr headwind I'm going to say I probably would have gone over the 295 that I expected. Got a very fast ET as well considering it was on AD08R street tyres on an unprepped airport runway.

Fastest pass here being a 18.106 @ 290.8km/hr with a half mile of 15.672 @ 180mph. The quarter mile was logged via GPS at a 10.2 @ 144.1mph

 

 

Edited by SimonR32
  • Like 2

Was not dissapointed with the stock block warriors! How your car consistently beats all of the big hp pretty looking ozzy park workshop builds is beyond me haha, those quarter figures would surely improve on a preped track yes? 

  • Like 1
2 hours ago, azzada1 said:

Was not dissapointed with the stock block warriors! How your car consistently beats all of the big hp pretty looking ozzy park workshop builds is beyond me haha, those quarter figures would surely improve on a preped track yes? 

Would expect radials and motorplex to be a bit faster but who knows... I may get off my ass one day but need at least 18s to clear brakes

18 hours ago, azzada1 said:

Was not dissapointed with the stock block warriors! How your car consistently beats all of the big hp pretty looking ozzy park workshop builds is beyond me haha, those quarter figures would surely improve on a preped track yes? 

Why would it shock you mate? you pretty much summed up most workshop cars in your reply. They supposedly punch out big hp on a dyno but the track is a different story.... online warriors love dyno figures lol

  • Like 3

What size oil drain do you guys use?

Precision say minimum -10 which was supplied with the kit i got but after looking at the drain size at the base of the turbo it seems too small.

I didnt measure the factory turbo drain but from memory (which is terrible) it would be closer to -12.

Is this a case of bigger is better or will -10 be fine.

20180313_133413_resized_1.jpg.b067d59f8183c41550ec4abf2e9768af.jpg20180313_133823_resized(1).jpg.077e37861967d8349e37faa3fa342514.jpg

2 hours ago, burn4005 said:

i wouldn't worry about the drain on a precision, most of the oil goes out through the shaft seals.

So I run one, know several others that run them for years with no issues. Every time I see issues with seals it always appears to be install error

5 minutes ago, SiR_RB said:

Bigger drain the better on precision’s 

and no sharp bends or kinks 

I can run -12 drain flange on the turbo then use a -12 braid hose with a 45 degree fitting on the top end with a 90 degree on the bottom going in to the block just in front of the engine mount. Hose should be almost straight with only a slight bend. Might might have another look to see if i can use a 45 bend in the bottom of hose too but not sure if ill have clearance.

 

3 minutes ago, azzada1 said:

I also use an earls inline oil filter for the feed.. and be careful you dont accidentally turn the oil restrictor when tightening the oil feed line

Ok cheers thanks guys ill keep an eye on that, i think the kit came with -4 feed and turbosmart filter

Alot of people dont run the filter and dont run into any other issues either, But lets not pretend precision hasn't had its fair share of complaints and quality control issues.. I fit the filter for my own piece of mind and ended up having issues with the first motor and filter saved turbo.. my drain doesnt have any fittings just the push lock -12 i think it was and a nice curve to the block with heat sleave over it to make it last.. 

Edited by azzada1

i guess it probably helps that i don't leave the oil in the car for much more than 1000klms as the car doesnt get driven a lot. Its extreme, but when it sits for 6 months at a time and runs E85 we prefer to just swap out the oil and oil filter. 

NEO25 - its been a while since i worked on a Skyline but is there any way you can run the front oil drain from an RB26 on your engine? it would make the drain very easy to make up then

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
    • Every one has seemed to of have missed . . . . . . . The Mazda Cosmo . . . . . . what a MACHINE ! !
×
×
  • Create New...