Jump to content
SAU Community

Recommended Posts

Could be a stuffed wheel bearing. I'm in the process (quite literally as we speak) of replacing my front ones because of much the same problem.

Did you get the rear wheels alligned too? Remember these cars have four wheel steering...

Could be a stuffed wheel bearing. I'm in the process (quite literally as we speak) of replacing my front ones because of much the same problem.

Did you get the rear wheels alligned too? Remember these cars have four wheel steering...

ok i'll give it a try and keep you posted on results, got to find time...

Thanks for the help

spacers? not too sure, will find out, they are aftermarket wheels

They are new rims, will get back balanced too

Thanks

Edited by Rbsushi
how long were the tyres unbalanced for?

if the tyres have been run unbalanced for a while they wear in a way that, when rebalanced, they unbalance themselves again

urgh and by unbalanced i meant out of alignment, shouldn't post when tired

I got new tyres yesterday, balanced and aligned, front and back.

after 1 day my steering tremors are back @80km/h, I'm going to change caster and sway bar bushings, cause mine are stuffed and get aligned again and see how that goes.

Take a look if your bushings need to be done.

that should only affect it when you put the brakes on. i had a magna that kept warping the front rotors every few months after getting them machined. they were really really bad. even at 60kmh by the time you had gotten down to 50kmh the vibration would be shocking and by the time you stopped it was ridiculously bad, but it never affected how the car drove when you weren't touching the brakes. ended up getting new rotors and it didn't warp them anymore.

I too am going for the bush route now because I've replaced wheel bearings and alligned/balanced everything so I can only put it down to the other weak link in steering gear; bushes. Either that or the mob who did my alligning/balancing did a shit job.

  • 2 weeks later...

I had to get mine balanced/aligned twice cos the first did indeed do a shit job, so don't take it back to the same place the 2nd time, likely they'll do a crap job still...

The only company that does good aligns seem to be Tyrepower and Beaurepairs from my experience.

I found out that my suspension is stuffed, crappy ones through pedders, new but now pretty much throw away, bad mistake, and all my bushes need changing. So off to fulcrum suspension, where I'll get some tein suspension, shocks etc; put in and replace the bushes with fulcrums polyutherine bushes.post-63012-1272202781_thumb.jpg

But now with the accident today, it's all been put on hold, man whats next.............

:P

I found out that my suspension is stuffed, crappy ones through pedders, new but now pretty much throw away, bad mistake, and all my bushes need changing. So off to fulcrum suspension, where I'll get some tein suspension, shocks etc; put in and replace the bushes with fulcrums polyutherine bushes.post-63012-1272202781_thumb.jpg

But now with the accident today, it's all been put on hold, man whats next.............

:)

Did the suspension contribute to not pulling up in time - out of interest?

Insurance job (even tho' it looks as if you'd be paying Excess)?

Hope the car is all good pretty soon!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: Tunehouse looked into the problem and identified a wiring issue between the camera unit and the connector. They managed to get it working , but did warn me at some point it will stop working again. From their perspective it is unserviceable and will need replacement. They did some research and found that the new replacement camera would be Approx $1400 supply only (their fitting cost would be $190) . They did provide the part number (28442-JL05B) and a quick google of the part number shows that these are rather expensive brand new (seemingly no longer in manufacture) for the places that still have them in stock, with the used option potentially presenting  the same issue down the track at some unknown point. They are happy for me to supply the part so that they can fit it. Decisions, decisions... I can definitely recommend Tunehouse (thankyou Vee37!). Cost for the diagnosis was as quoted  ($190) , car was ready on time and communication was top notch. Their workshop is super clean and modern, and there was plenty of car candy parked out the front on the day I went.   Would definitely go back.   
    • to fix the voltage drop issue I swapped out the old 150amp alternator which turns out is a brand known for having issues and replaced it with the black 180amp alternator beside it 
    • For anyone interested, the Way Back Machine has that Japanese website archived with pictures, etc: https://web.archive.org/web/20051023225805fw_/http://www.a31cefiro.com/air_con.htm "Simply swapping the wiring of the harness will not allow it to function properly. For the outdoor air sensor and sunlight sensor, disconnect the wiring connected to CN1-11 of the air conditioning harness from the harness and connect the sensor side wiring to earth. For the indoor air sensor, disconnect the wiring connected to CN2-3 of the air conditioning harness from the harness and connect the sensor side wiring to earth. The connector PIN numbers listed here are the genuine A31 PIN numbers. To avoid incorrect wiring, check with a tester before wiring. Also, disconnect the wiring in a location close to the sensor. The disconnected harness side wiring will not be used, so be sure to insulate it." Wish someone sold a conversion harness to just plug-and-play a Kouki 180sx digital climate control into C33/A31. I'm decent with wiring but feeling kinda lazy about taking this on. Edit: Did some more digging and found a helpful Minkara blog post about the conversion as well: https://minkara.carview.co.jp/userid/1831116/car/1360568/2284209/note.aspx "After installation is complete or the battery is replaced, you need to go into self-diagnosis mode and set the internal air recirculation. The way to do it is to "hold OFF with the key on for more than 5 seconds, set the number to 5, then press 卍→C." ↑↑↑It probably won't make sense unless you actually try it (・∀・)." Lol wtf
    • Maybe SAUNSW could see howany members would do a motorkhana day if Schofield's is still available for a reasonable price...
    • Skip the concrete, we just need to smooth a field. Mark knows how to drive a grader Duncan   I reckon 100x100 flat area for skid pan style, and then some sort tracks for rally... Duncan's already got a rally car on the premises to...
×
×
  • Create New...