Jump to content
SAU Community

Recommended Posts

yo peeps

my mates RB25 (s2) is all of a sudden making a funny noise kinda sounds like a bearing

it was fine like a week ago, hasnt been driven.. now all of a sudden this noise

tried unplugging vvt but that didnt fix it, it feels like its coming from under the rocker cover

the engine is stock, unopened etc

<object width="480" height="385"><param name="movie" value="<A href='

name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="<A href="
type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
Link to comment
https://www.sau.com.au/forums/topic/314501-rb25-making-funny-bearing-noise/
Share on other sites

take it to a mech. asap! i wish i had gone to see one earlier. i started hearing a similar noise, took it to my mech, turns out harmonic balancer had come loose... left it too long and had damaged my crank :D

hopefully this isnt your problem.

-trel

This is screwed... i have just changed the spark plugs... but i took it for a few drives and it never made any noise..

Then a couple days before i moved overseas i started the engine and it was fine no noises at all..... so i dno how a noise like that could suddenly come up?

worst of all is i now like in U.A.E and im trying to get rid of the car soon as possible.....

Could be valve guides in the head. :worship:

i dont see how the valve guides could make that noise?... i dont think its the valves themselves because i bent valves and it make a different sound to that..... so i dont think its bent valves.

if valve guide were stuffed... then oil would be getting into the cylinders and there would be smoke coming out the exhaust?

I hope it could just be the water pump?

otherwise what sort of bearings are in the head?

Idler pulley bro.

It sounds SO much worse than it is though huh? I crapped myself when mine started doing it. But with mine it went away after the car warmed up.

Check out my vid:

Same noise more or less. I changed my belts/idler/tensioner, goneburger :P

Idler pulley bro.

It sounds SO much worse than it is though huh? I crapped myself when mine started doing it. But with mine it went away after the car warmed up.

Check out my vid:

Same noise more or less. I changed my belts/idler/tensioner, goneburger :P

thanks for that man very helpful! i will get a gates kit and replace everything, its due for it anyway

let you guys know the results

if your not sure take it to a mechanic that is..... to me it sounds like it may be a few different things so best to take it to someone that can u tell u for sure and pinpoint the problem before it gets worse....

could me your lifters if u say it started doing it after sitting there for alittle while.

if your not sure take it to a mechanic that is..... to me it sounds like it may be a few different things so best to take it to someone that can u tell u for sure and pinpoint the problem before it gets worse....

could me your lifters if u say it started doing it after sitting there for alittle while.

the timing belt is due anyway so doesnt bother me or the owner to change it, he's giving me $100 to do it anyway :D

its not the lifters i know what they sound like

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Hope the cans went down well at least 
    • 255 can't go wrong with the price.
    • When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...