Jump to content
SAU Community

R34 Saftey 21 Roll Cage

C4NC3R
 Share

Recommended Posts

C4NC3R Contributor

C4NC3R

Posted
Posted

Cusco/Saftey 21 6-Point bolt in full cage

For R34 2-Door, bought to track the 34 but I'm getting a 180 as a track car instead, so need to sell it. The R33 ones of these on Nengun are $1000+. It comes with all of the mounting plates, bolts, cusco foam to cover the whole thing.

Located in Perth, Western Australia. Postage to Melbourne is $200ish so yeah will post at buyers expense.

Price; $800 ONO

0420 307 580

[email protected]

safety21-cage.jpg

Link to comment
https://www.sau.com.au/forums/topic/315185-r34-saftey-21-roll-cage/
Share on other sites
GUN_METAL_GTR32 Grand Master

GUN_METAL_GTR32

Posted
Posted

hay mate

yeah u should still be able to have rear seats in but u have to cut a small hole for them to fit as all r34 cages mount to the same place which is the wheel arches. ill put some pic up tonight of how they mount my cage however doesnt allow for back seat passengers so mine are removed.

my friend has one of these in his silvia and has kept back seats with a small trim and u can still sit in there.

8110 - the middle hoop is connected to the front and rear section of the cage by bolts so it is all removable. i already have a half cage (rear section) so i just want the front yeah.

op - i need some photos of how the front connect to the roll over hoop and they need to be high res and of both side just so i can estimate where they will bolt on to mine as i have an interesting cage set up

C4NC3R Contributor

C4NC3R

Posted
  • Author
Posted

Sure guys, I'll smash some photos up in a bit from my DSLR, I havn't put it together so they'll just be of the pieces.

If you're both keen, cause you're both in Melbourne would be cheaper to post, either work out between yourselves how you want to divide the cost or I'll do it for you, up to you.

C4NC3R Contributor

C4NC3R

Posted
  • Author
Posted

I got it from Japan, via Melbourne, and the leg between Melbourne to Perth was $200. I'm keen to get it out of here to buy new turbo and such, so if you're over east then I'll do it for $700 plus postage, to make the postage cost a little lower.

And Geraus, I'm not sure if it would or not, I'm sure with enough cutting of thigns you could get it to fit but yeah. Worst things worst you'd have the cage there in Melbourne, and there's a lot more people who track R34's over there =p

C4NC3R Contributor

C4NC3R

Posted
  • Author
Posted

I got it through Import Monster, found it online and got them to bring it it, it's not something they stock. I'm losing a heap of money on it, paid more to buy it in Japan than I'm selling it for, not including the shipping.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Milkmun
      S15 Spec R

      By Milkmun · Posted

      Wow that's a steal, you've done well there. 
    • trey318
      r34 gtt led globes

      By trey318 · Posted

      Exterior LEDs R34 2Dr R34 4Dr Position Lamp T10 T10 Winker front T20S T20S side T10 T10 rear T20S S25S150 Anti-hyfla relay TYPE3 TYPE3 tail T10 T20W Stop Lamps T20W T20W High Mount T16 T16 back T16 T20S number T10 T10 trunk T10 T10 Interior LED Item No.     Map Lamp BA9S single-sided     Room Lamps T10×31     Trunk Lamp T10     meter Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     Liquid crystal section T6.5 pedestal     Winker T6.5 pedestal     High Beam T6.5 pedestal     3 SERIES METER Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     air conditioner Early Liquid Crystal T3     Late LCD T4.2 Short     button T4.2 Middle     Hazard SW T3 Pedestal Short     Keyring T5     Cigar Socket T5
    • KyoyaR33
      Rebuilt Rb25det issues

      By KyoyaR33 · Posted

      Howdy all,   I had my rb25det S2 rebuilt and finally started it today but have run into a few issues  Engine sounds like a a diesel easiest way to summarise like small ticking, gets louder when revs are slightly adjusted  The engine builder repainted the engine cover leaving no where for me to go off with lining up the CAS so have it as central as possible so not sure it that could be affecting it?, changed the gearbox fluid too but won’t seem to go into gear when running, and only 1 to 4 when off having a hard time finding 5th and reverse anyone got any ideas or a base for me to start off? much appreciated 
    • GTSBoy
      Neil's R33 Gts-t Build

      By GTSBoy · Posted

      Well, no. It's an 023, which is pretty similar to an 040. Although it is hard to tell from the specs, as given.
    • GTSBoy
      My R32 Money Pit & The Headaches That Come With It

      By GTSBoy · Posted

      Hmm. Maybe the (other thing I forgot about!) Haltech removes at least some, if not all, of the problem I described. I guess there is still the possibility of getting it wrong if the AC is set up/wired up for the Haltech as if it was in an R34 (simply because it's on a Neo), and that's playing foul with the R32 AC computer.
×
×
  • Create New...