Jump to content
SAU Community

Recommended Posts

Taken from their facebook page: http://www.facebook....229267523757328

eiujpd.jpg

TFR-6584%20Fuel%20Rail%20Nissan%20ECR33-228x228.jpg

got the same thing here for under 100, use alot of them too when we fit id1000cc http://goodiesdirect...&product_id=405

  • 1 month later...

wish i knew before about this F*kn manifold..

someone must have run top feeds with a plazmaman..

I am having the same issue fitting id1000's and the plazmaman top feed rail. Did you get an early version of the plenum? I did, and i have had all sorts of trouble with top feed fitment, however they have since changed the design and it should clear up the issues your having. Give them a call, im sure they will be happy to fix it up for ya.

Can some one post a pic of there id2000 install into an rb manifold. Need to lnow what rubbers or oring u have used where the injector seals into the port.

From memory I bought two sets of seals from autobahn. Picked out the right sizes and it was all good.

  • 1 year later...

a bit of a thread dig sorry guys,

trent, does these takashi fuel rails you have used in the past, do these clear the plazmaman plenum when using 11mm 1000cc injector dynamics? and when you do use them are you using id1000's with no top hat installed?

TFR-6584%20Fuel%20Rail%20Nissan%20ECR33-
got the same thing here for under 100, use alot of them too when we fit id1000cc http://goodiesdirect...&product_id=405

a bit of a thread dig sorry guys,

trent, does these takashi fuel rails you have used in the past, do these clear the plazmaman plenum when using 11mm 1000cc injector dynamics? and when you do use them are you using id1000's with no top hat installed?

I am using a HKS rail with full height 2000cc injectors and plazmaman rail... Pics in my build thread in Sig if you can find them!

hmmm i wonder if yours being a neo rb25 would be any different. i actually wouldnt have thought that full height injectors would have fitted up all ok. is the hks also an 11mm rail?

Trent if you do see this please let me know!

cheers

hmmm i wonder if yours being a neo rb25 would be any different. i actually wouldnt have thought that full height injectors would have fitted up all ok. is the hks also an 11mm rail?

Trent if you do see this please let me know!

cheers

I dont think it would be any different in terms of height.

And yes, it is an 11mm rail. There are plenty that have done it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
    • I would agree, unless you need something specific to the HV motor/battery side repaired or investigated, any mechanic will be able to perform normal services, but if you prefer, maybe look for a mechanic who regularly services/repairs Nissans, the VQ engines are pretty common in the Nissan lineup.  Sorry, I can't make any suggestions, I don't live in Vic.
    • Some of them keep working fine. 9 out of 10 of them end up causing an absolute misery bleeding the system and get thrown on the workshop floor in a tantrum and never thought about again because they were never really needed and just added crap to the car that we could have done without. Same-same with HICAS, A-LSD, and various other stupidities that over eager 10x engineers thought we had to have.
×
×
  • Create New...