Jump to content
SAU Community

Removing Piggyback Ecu

greensa14

By greensa14,
in Engines & Forced Induction

 Share

Recommended Posts

greensa14 Collaborator

greensa14

Posted
Posted

Hi all,

I got done by the EPA. I need to remove my Piggyback ECU (UNICHIP). Is it just a matter of pulling it out, and removing the relevant wired up connections?

I also have larger injectors, and Z32 AFM. I will be removing these and replacing with stock items.

Once these are removed i just reset my ECU and the car will run?

Or is there anything else i need to do for it to run off standard computer?

Link to comment
https://www.sau.com.au/forums/topic/315807-removing-piggyback-ecu/
Share on other sites
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

You will see that some piggy backs actually run in series with the ECU wiring, just remove the piggyback & join back the relevant wires.

As long as you replace the aftermarket larger injectors & Z32 your car will run fine off the standard computer. Also make sure your base timing is correct to, the previous owner/tuner may have adjusted the CAS to suit the piggy back.

Turbo Dave Collaborator

Turbo Dave

Posted
Posted

I pulled the Kick Panel off my GTR today, when I bought the car I was told it had a MIMO Piggyback (Dunno What that is) but cant actually see anything that looks like an ECU of any kind only a little brown box with some heavy gauge wires coming out of it, Plenty of Splicing though!!

post-34973-1270690830_thumb.jpg

post-34973-1270690891_thumb.jpg

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

greensa14 - totally depends as others have said - how the UNICHIP is installed.

Perhaps get some pics?

If you have to unwire it and so on, it's going to be a pain in the ass.

You'd be better off with a PFC or something that is a replacement setup - 30 sec to remove from the factory harness.

Ok thanks for clearing that up I will have to look a little deeper, has Nismo AFM's so there has to be something in there surely!!

Open the cover. I'd say it's a chip on the actual ECU board.

There is no way you'll have aftermarket AFM's without a chip to alter it as there is no wire-in piggy back in those pics :woot:

greensa14 Collaborator

greensa14

Posted
  • Author
Posted

I had a look last night. It is an external ecu that has been tapped in to the other wires on the factory unit to obviously change the readings as they pass through.

So it looks like i need to remove the spliced wires and re-solder the factory ones so they dont bypass.

Yea PFC would be good, but over worrying about defects etc. Dont want anything visible.

Looking at going Nistune.

Duncan Grand Master

Duncan

Posted
Posted

why is a nistune (or unichip for that matter) illegal? they are not programmable on the fly, and the factory ECU is just as retunable as they are.

Surely the final emission is the only issue for legality? Plenty of shops in NSW that can provide a tune that will get you past the emissions test, why would Vic be different?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
why is a nistune (or unichip for that matter) illegal? they are not programmable on the fly, and the factory ECU is just as retunable as they are.

Surely the final emission is the only issue for legality? Plenty of shops in NSW that can provide a tune that will get you past the emissions test, why would Vic be different?

Nistune can be retuned - the EPA here is retarded is the basic sense, archaic laws with no common sense.

Unichip go through the ADR testing/approvals, Nistune has not and can be retuned anytime.

Unichip you have to go back to them for (assumingly).

darkhalf Community Regular

darkhalf

Posted
Posted

What is the criteria for an aftermarket system to meet ADR over there?

Nistune board can be PIN locked once the tune was able to meet emissions. The only way to retune it then is use the original PIN or reflash the board outside of the ECU

Transport SA documentation I have previously read states that any aftermarket/reprogrammed ECU will not be accepted due to the cost of the emissions testing required. However things may have changed since that was published

Cowboy1600 Grand Master

Cowboy1600

Posted
Posted

Cause we have some whack ideas down here.

A number of rules surrounding car modifications make zero sense.

The 1 intake mod for example. Senseless. No aftermarket ECUs....senseless.

I might get in touch with my local member and get her to ask Tim Pallas for a "please explain".

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
What is the criteria for an aftermarket system to meet ADR over there?

Nistune board can be PIN locked once the tune was able to meet emissions. The only way to retune it then is use the original PIN or reflash the board outside of the ECU

Transport SA documentation I have previously read states that any aftermarket/reprogrammed ECU will not be accepted due to the cost of the emissions testing required. However things may have changed since that was published

Vic is near enough to the same for the sake of the conversation.

PIN lock means nothing.

If its reprogrammable, not factory, its not allowed until all the full testing is done.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      I ❤️ Matty I would like to thank Matty for going out his way in securing me a OEM NC detachable hard top for the NC Matty, your worth your weight in gold, and I cannot say how much I really appreciate your outstanding help I'll get it colour matched once I pick it up sometime in Dec-Jan 😁  
    • Rezz
      OEM Soko: Japanese business supplying Automotive items from Japan - Freebie inside!

      By Rezz · Posted

      We have some genuine Japanese legally decommissioned car number plates now in stock 🙂 Add some legitimately obtained JDM style to your Skyline or other Japanese model, or simply as a garage/man cave decoration! About the 40mm hole: The Ministry of Land, Infrastructure & Transport in Japan recognised the popularity of keeping decommissioned plates among car enthusiasts and came up with a method to "destroy" (or render them unusable for street use) while still retaining their collectable/usable value for display etc.  We have 40mm hole covers available to cover the hole nicely with a Sakura motif, which are also available in white in (very!) limited quantities, however they frequently sell out. Please let me know if you're wanting one or more of these and I'll check availability. The Sakura motif covers are more common. https://www.oemsoko.co.jp/products/genuine-decommissioned-japanese-vehicle-number-plate-set-su-7515 https://www.oemsoko.co.jp/products/genuine-decommissioned-japanese-vehicle-number-plate-set https://www.oemsoko.co.jp/products/genuine-japanese-vehicle-number-plate-400mm-hole-cover *Please note that we can't obtain particular number or area name (eg: "Gunma 500 Fu ・86") if requested. All plates are provided as they become available after decommissioning. 
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      Ah, fair enough. For the IAT, I'm using a legit GM sensor that was used on the car prior to my current build. I'll get another wideband and IAT ordered and follow up when they show up. Thanks for the help.
    • GTSBoy
      RB20DET lean on cold start

      By GTSBoy · Posted

      You shouldn't need to massively fatten up the mixtures for cold conditions. For one thing - 0°C is not that cold. For another, the Haltech will be using the IAT sensor to tell it how dense the air air, and calculate the correct amount of fuelling. Then the cold start enrichment is added as a % on top of that, so it should scale with the main fuelling. You might also doubt the IAT sensor at this time. You're not using one from an RB26 are you? Using a nice Bosch sensor or similar? Happens. Some wideband units take great pleasure in killing their sensors. Put another wideband in the tailpipe and compare. Or just swap the sensor to a brand new one and see.
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      Oh, my misunderstand. When the car was running, it sounded ok, but if I gave it any gas it wanted to die but caught itself afterwards. It's very different from how it was a couple months ago when it was warmer outside. The logs show that the AFRs are better during, what I assume, is warmup enrichment. Because it's cold, and air is more dense, should I work on the enrichment bit?
×
×
  • Create New...