Jump to content
SAU Community

Xenon Hid Reinstall

prdreilly
 Share

Recommended Posts

prdreilly Contributor

prdreilly

Posted
Posted

I was looking in behind my headlights and as far as I can tell everything looks to be in tact to refit my HID lights. The wires that go into the ballast have been cut and rewired to the halogen bulbs. The ignitors were neatly tucked in behind the headlight and seem to not have been tampered with.

Now what exactly is involved in reinstalling my original bulbs. It looks like some kind of spacer device has been put in for the halogens bulbs to fit.

Also, there is a yellow wire that is attached to the back of the headlight and into the back of the ignitor, is that part of the original wiring or to do with the halogen change?

Any help appreciated. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/317189-xenon-hid-reinstall/
Share on other sites
prdreilly Contributor

prdreilly

Posted
  • Author
Posted

Well, undoing the 3 screws pulls out the globe mount and when it is out the spacer for the halogen bulb just pops out. Then the little wire clips that hold the bulb in, need to be bent to fit the Xenon bulb. I left the yellow wire attached, soldered the original wires back together and voila!

One HID headlight now working. Sure makes the old headlight look yellow!

Think I'll use crimps to join the wires on the other side as my soldering iron was struggling with these wires.

Also popped in my $4.45 "ebay special" SMD LED parking light, which matches the Xenon headlight nicely.

prdreilly Contributor

prdreilly

Posted
  • Author
Posted
Do you know if it is possible to get the other bulbs that point down and wide to match up colour wise and match the whiteness of the Xenon? Or would it be too bright to have them both on you went the Xenon's anyway?

Not sure exactly what you mean, do you mean the lower part of the lights (High Beam and Fogs)?

It sounds like fog lights you are describing, that light up down and wide. The are the same bulb as the High beam, must just have two settings. Not sure if they are standard type bulb, or a unique to Nissan item?

It does seem a bit silly having Xenon low beams and Halogen fog and high beam. I guess the cheapest option is to see if you can find a replacment bulb that is the white colour of the Xenon HID low beam. There are lots of imatation HID's now, that look as white, and don't need the ballasts and ignitors etc.

I wouldn't mind a better high beam, I find it pretty ordinary!

  • 2 weeks later...
FlyingEL Rising Star

FlyingEL

Posted
Posted (edited)

I have the same problem with you, prdreilly. The car was sold to me with a halogen bulb head light. I too found some kind of spacer/adapter for the H3C halogen bulb. It's glued in place so Using a screwdriver, twist and lift will pop the spacer/adapter out. You will need the 3 part for the HID to work. My car came with the ballast, the clipped power pin but missing the Igniter. Got them from Ebay (which is not cheap) and the HID D2R bulb (price depend on what brand you choose). Connect the wire from the halogen setup to the power pin of the HID. I bought a 6000k but I think 4700k give a better lighting. By the way, I do have an extra PIAA 4900k H4 bulb for your high beam/spot light for sale. PM me.

post-53067-1273140067_thumb.jpg

Edited by FlyingEL
prdreilly Contributor

prdreilly

Posted
  • Author
Posted

I was fortunate enough to have the Xenon bulbs and plug with cut wires for the ballast kindly put in my glove box after compliance. The ignitors were left in tact, so there was no need for me to buy anything, just had to cut the wires to the Halogen bulbs, pull out the spacers for the halogens and the bulbs (my spacers weren't glued, just pushed them out), then bend the wire springs that hold the bulbs in place, join the original wires back together (solder & heat shrink or Crimps), plug it all in and voila!

It is a bit of a fiddly job, you have to pull the wheel off, and the plastic guard liner to get to the back of the headlight, but I am pretty useless mechanically, so unless you are a total novice you should be ok.

prdreilly Contributor

prdreilly

Posted
  • Author
Posted
No doubt this will be an incredibly dumb question BUT...

seen as the factory HIDs arent self levelling, corner sensoring etc can i just buy an aftermarket HID kit from our vendors for example and install that?

You could, but obviously it will cost you. If all your Xenon bits are already there, and all you have to do is put it back together, that is cheap to do.

prdreilly Contributor

prdreilly

Posted
  • Author
Posted
Oh ive been wanting to refit my HID's but ive got no idea how to do it and dont really know much about headlights would u say its easy enough to do or should i take it to an auto elec?

First thing to do would be check that your ignitors are in tact, if not you have to decide if you can be bothered with the expense. Did they give you the original plugs that go into the ballast? If not, then you are going to have to chase up all those parts as well.

FlyingEL Rising Star

FlyingEL

Posted
Posted
It is a bit of a fiddly job, you have to pull the wheel off, and the plastic guard liner to get to the back of the headlight, but I am pretty useless mechanically, so unless you are a total novice you should be ok.

Huh? I though you have to take the whole bumper out and then you can get the headlights off. I think that will be easier but take longer time.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

bumper and headlight is the correct way. you can get at it by leaning the inner guards out of the way but if the ballast has been pulled OUT then its a front off exercise. I do the simple way if I CBF'd ripping off the front.

TUFF_350 Proficient

TUFF_350

Posted
Posted
You could, but obviously it will cost you. If all your Xenon bits are already there, and all you have to do is put it back together, that is cheap to do.

If i did decide to go this route, would it be the H1 or D2R kit? I searched the OSRAM site and they say its D2R for HID but i thought id check :S

Oaksey Enthusiast

Oaksey

Posted
Posted
Not sure exactly what you mean, do you mean the lower part of the lights (High Beam and Fogs)?

It sounds like fog lights you are describing, that light up down and wide. The are the same bulb as the High beam, must just have two settings. Not sure if they are standard type bulb, or a unique to Nissan item?

It does seem a bit silly having Xenon low beams and Halogen fog and high beam. I guess the cheapest option is to see if you can find a replacment bulb that is the white colour of the Xenon HID low beam. There are lots of imatation HID's now, that look as white, and don't need the ballasts and ignitors etc.

I wouldn't mind a better high beam, I find it pretty ordinary!

Yeah that's what I was wondering, thanks.

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • kevboost7
      Magnetic Drain Plug Snapped in Half

      By kevboost7 · Posted

      Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • MBS206
      New fix for low tyre pressure from bmw

      By MBS206 · Posted

      Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • sunsetR33
      Anyone know this frontpipe?

      By sunsetR33 · Posted

      Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • dbm7
      New fix for low tyre pressure from bmw

      By dbm7 · Posted

      Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • joshuaho96
      Anyone know this frontpipe?

      By joshuaho96 · Posted

      You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...