Jump to content
SAU Community

Recommended Posts

I had my R32 GTR Dynoed a couple of months ago. It had a pissy 139kW at all 4 wheels. The place that did this for me said that this was as per normal for a GTR. For a sum of approx $5000 they could easily get me 200Kw at the wheels.

Since this time I have heard that Standard GTR's should have approx 175Kw at the wheels. Can anyone confirm this????

Does anyone have any ideas as to why my car would be down so much in power. The only modifications are blow off valves and a HKS exhaust. The importer has done a dodgy job of installing a cat converter - but would this take away this much power.

Any advice on places to look would be very helpful. I don't want to go to a shop again as they seem to just want to get your money and rip you off.

Link to comment
https://www.sau.com.au/forums/topic/31756-r32-gtr-low-on-power/
Share on other sites

Have you driven other GTR's? Reason I'm asking is that before I got my car dynoed at 2 places and I got 2 very funny readings. Apparently I get more power at 4 wheels than 2 wheels???? Personally I don't live off dyno figures, the dyno is just a tuning tool.

You running bigger rims BTW? Mods? This also affects dyno figures.

You should be getting more power in 2WD mode than in 4WD mode. 139 @ 4 wheels sounds about right when compared to 175 @ 2 wheels. (My GTS4 runs 115 and 145).

Dodgy cat install could well be creating too much back pressure, which will adversely affect power.

If you want more power, check out the latest HPI (GT-R special edition #4) for some cheap yet effective power enhancements.

For a sum of approx $5000 they could easily get me 200Kw at the wheels.

Watch out for places that tell u that your car is running shit and then say for x amount of $$ we can make it do this as its very easy to bodge dyno figures.

Take it to another dyno and get it checked out

I haven't driven any other GTR's. But i have driven many other fast cars. There is no way my car wouold be able to cut a qtr mile time in the 13's. I think it would struggle to be under 15s.

Does anyone no a decent shop in Sydney I couls take my car too and get an honest assessment???

That dyno figure does not sound right. My 32 GTR is running at 160kw at all 4 without aftermarket exhaust or cat. Have been told that is poor too! A lot of car that come out of japan run to rich. What is fuel comsumption like? Should get at least 400 to 450 out of a tank. $5000 to get to 200kw is a joke! If you have a good exhaust, hiflow cat, HKS cam gears and a good tuner you should be able to make 200 to 250 with a bit of extra boost.

Call Ben (racepace motorsport) in Melb. to set you on the right track (0397629421). A 500kw at wheels R33 GTR is all the qualifications this guy needs!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next pic will probably bring back Charlie's PTSD So yes, pump is back out. I hooked the fuel return up to a hose into a container to flush out the first litre or 2, jumped the Fuel Pump relay and.......nothing.... Turns out the pump I had pulled out, checked, cleaned everything....was dead.  I hadn't actually hooked 12v to it to check it worked before I put it back in. Anyway...Neil had kept the old pump which still worked, so I just swapped it back in. All good, flushed the lines out, ready to start
    • OK....so something that works like it said on the tin! Fitting the pressure feed into the car was an absolute PITA because the oil filter is in the standard location and then there is a fitting to run to the oil cooler. On the other side between the filter and the steering box is the standard oil pressure sender (not working for some reason, something to check) and 2 tapped 1/8 BSP threads for the oil temp and pressure gauges. Unfortunately it is really tight in there and it took a hours of stuffing around to get a t fitting to connect the priming pump and retain the gauge sender.  Also, the Aeroflow sump has some massive drain plug (needs a 32mm spanner) so I couldn't use the regular fitting there either. In any case....once it was all hooked up, like magic priming.mp4 15 sec, 3 bar of oil pressure. Left it running a couple of minutes to push through everything, looked good   
    • Yeah the latest style kit has been trouble free, I've done a fair few klm on it including pushing a bit on low fuel and it hasn't been surging (that's not an endorsement for race use, I haven't tried that low, or that hard cornering!). For street use it has been a good thing, handles the high current OK, only real issue is it is not cheap
    • So, how do you feel about the Frenchys surge tank setup @Duncan? Have you had a chance to try it out more? The sketchy wiring in my fuel pump setup has decided to melt and die and I'm looking for a solid replacement now. My fuel hat is toast so the Frenchys kits providing it all look promising.
    • Yeh... literally every time i jump on a forum, see an instagram post or see an engine bay at a car show, i get an idea and add it to my 'to do' list. So what started off as, hey can u just make a couple of intake hard pipes because my dumbass bought the wrong apexi kit, blew out into a 2 week job including braided brake lines & custom bash kit for the front lip haha.  Getting Luke from A4E engineering to make a full custom exhaust with a controllable aes dump valve so i can actually switch between quiet and loud, because right now its just loud all day every day. Then after that go and get the tune redone flex e85 & 98 as i get bugger all milage from e85, makes going for longer drivers difficult
×
×
  • Create New...