Jump to content
SAU Community

Recommended Posts

Hey, i got to watch my car on the dyno the other day and noticed it had heaps of air/white smoke coming out the cam covers breather hole as i had the catch can setup disconnected, it started at 3000 as it started to make boost and by 7000 it was a pretty substantial plume of smoke/air, alot more smoke than i would of expected for blow by..

The engine has done roughly 1300kms, used 9:1 cp pistons and rings, i compression tested it the other day when it was cold, since the car is missing a radiator atm and got roughly 158-160 for pistons 3-6 and 155 for 1 and 2, wont be able to compression test it warm until i get my new radiator.. should i get a leak down test done as well or is this usual for a forged engine and im just being a bit paranoid?

Cheers

Jarrod

Link to comment
https://www.sau.com.au/forums/topic/317913-concerned-with-new-engine-on-dyno/
Share on other sites

i built it myself, first time i have attempted anything like this, made harder by the choice to ceramic coat everything

Elite Racing:

Cheers for the advice, i just wasnt expecting it to breathe so much.. almost looked like more air was coming out the breather than the exhaust

Jarrod

i built it myself, first time i have attempted anything like this, made harder by the choice to ceramic coat everything

Elite Racing:

Cheers for the advice, i just wasnt expecting it to breathe so much.. almost looked like more air was coming out the breather than the exhaust

Jarrod

Yeah a lot of people freak out when they see it. It's gas fumes created by the approx 10%-15% of leakdown that every engine has. Imagine the cylinder pressure once you throw in 15 to 20 psi of boost. On a 100psi regulated leakdown test you would see a value of approx 15 psi escaping. When you are cramming boost in and combustion pressure also, that increases to around 300psi cylinder pressure or there abouts possibly more. So you can have around 40-60 psi of pressure bypass the rings but not constantly. It's just little amounts as the combustion and stroke is so fast.

Add 6 cylinders all doing the same thing and it's almost like a mini steam train if you leave the breathers off.

With compression of 160psi on all 6, it sounds like you did a decent job of the build.

It's when it starts blowing raw oil out that you need to be concerned.

My did the same thing, even blew a bit of oil out of the catch can, that was even after running the engine in after 5000k's. Found that after the motor ran had done approx 7k, the breathing stopped. On the other hand, a mates 32 GTR does the same thing and has done more k's then I have and he's using CP pistons and rings like you. I had read somewhere that the CP rings had dramas with sealing properly and scoring the bore, but I think they fixed that problem. See how it goes with a few more k's on the engine, it might settle down.

Elite Racing:

thanks alot for that elite, thats a real load of my mind, my main concern was that i had done something wrong or it was something out of the ordinary, a mini steam engine is definitely the right description for it.

116.hks:

Yeh i had heard that as well and that they had fixed it as i was considering sticking in ACL rings, hopefully it seals up a bit better as it clocks up more kms.

Cran:

haha jason, ill make it there oneday, just got to figure out why the torque was dropping off earlier now.. which i think is due to the cams maybe being advanced, hopefully the radiator arrives next week sometime and the car will have the new exhaust made up.. and ill be able to take you for a spin

Jarrod

Status: id say it was steam.. more so than smoke.. i just remember thinking it looks alot like a kettle.. my piston to bore clearance was 3.5 thou from the pistons size before they were ceramic coated, the ceramic shop said because the pistons were getting ceramic coated they wouldn't expand as much. So the dry film lubrication layers thickness wouldn't effect the piston to bore clearance.. hard to say exactly what the clearances were without buying a micrometer and checking them myself, which i was considering, the bore was bored out 1 thou extra than the specs since the machine shop measured them and claimed the pistons were all 1 thou bigger, which i had double checked by a engineering shop.. i did roughly check the clearances with a feeler gage, but considering the bore and pistons are both round n they feeler gages dont like to bend it isnt very accurate, off memory (which isnt very good) i managed to get the 1.5 thou size in, but the 2 thou clearance was extremely tight..

Jarrod

when i was looking at r32 gtrs begining of the year, i had this white one idling, i opened the oil filler cap on the engine, it was "choofing" masses of white misty air, it was pretty high pressured too the smoke was almost going up to the bonnet !

what does this exactly mean? i always thought it was blow by/ alot of blow by, so im assuming worn rings? low compression ?

What does it smell like? If the rings aren't sealing correctly it will have that combustion/oily smell. Makes ya feel a bit sick in the gut after a while. From what I've seen and heard, it only has happen to motors running CP piston and ring combo. Just keep an eye on it mate, if it does stop with more k's, get it checked.

i didn't end up sticking in a oil restrictor as i did the internal vct oil feed where it gets its oil feed from the oil gallery, i assumed once the vct turns off after 4k that the oil would also be draining from the vct oil return line, i did install the rear oil drain kit and drilled the oil returns out larger in the head, which seems to be adequate enough

Cheers for all the input guys, ill monitor if it changes over the next few 1000kms and see if its losing any oil

Jarrod

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, thumbsup from me. The distant shot of the bay just looks same-same as before.
    • Dad had a court case drag out with them from 1998 to 2004. He was in a not at fault accident, NRMA were the ones who covered the other person. They tried to blame his neck injuries on the fact he'd had an injury in 1981 on his extreme lower back where he slipped a single disc right near the bottom. Had been all cleared from that injury for years. This accident destroyed his shoulder, and f**ked a heap of discs in his neck, and he still has major problems with it to this day. Sarah's sister while on her L plates had a small Suzuki Alto, she had stopped to give way to an ambulance, and someone changed lanes behind her because there lane was also slowing, and rear ended her at 80km/h. (She had been stopped for a few seconds already too!). Car was completely f**kED. NRMA sent the vehicle around to 3 different workshops as they kept claiming "We believe it can be repaired, and not written off, we just need to find the correct workshop". It took 3 months, and a lot of arguing before they'd concede and wrote it and paid out. About two years later her sister had a Lancer, someone pulled out of a stop sign without stopping (in an 80 zone). Her sister swerved, hit the front of the other persons car (Instead of dead t-boning the drivers door), which ramped her Lancer, and made it roll multiple times down the road. It hit every panel on the way through. Her sister had slid her self out of the car, and remembers the ambos walking to the accident (They'd been sitting at a set of lights just down the road and witnessed it) and they were saying "Well, this ones going to be a fatality, no way you can walk away from that". Well, she did. And then NRMA sent two assessors out to look at the car, both of which wrote it off. They tried to send another assessor out, except a HUGE uproar was raised, and they FINALLY paid it out. That was on a car, that had damage to EVERY panel, you could see from 100m away the whole car was also twisted, roof bowed etc. Nah, we'll try get out of needing to payout on a $10,000 car... Her sister ended up with major shoulder reconstructive surgery being required, and was permanently limited in her ability to do her job as a nurse after that, as she can't (And was told before surgery too this would be guaranteed to happen) regain full strength in that shoulder. However, there was no choice to not have it, as she could barely use her arm, which was her dominant one, and was in near constant major pain. (And she's the type of person that would try and walk off a broken leg!) NRMA did the biggest run around on the personal injury side too for about 18 months, even to the point of trying to put 100% blame of the accident on Sarah's sister, even though the other driver admitted she didn't look, and didn't stop, and was charged by the police. Sarah used to have a Barina insured with them. It was a policy setup, paid all 12 months in advance. At the end of the 12 months, Sarah was living with me, I reviewed the renewal, it clearly stated "If you do nothing, your policy will cease on XYZ date". We did nothing, as we moved her insurance in with all of mine and I was with Shannons. We find out 10 months later, NRMA decided, because he DAD had a car insurance policy at the same address as what Sarah's mailing address was (Garaged address had been changed), that they'd put Sarah's (What should have been non existent policy) onto her Dad's month to month charges on his credit card. We had to jump through hoops, to get a refund. They didn't care that we actually found the letter that said "If you do nothing, your policy will cease" they made us prove we had NON COMPULSORY insurance else where before they'd issue the refund, and after they agreed to the refund, it still took another 6 weeks and 3 more phone calls for them to actually process it. They also had two insurance claims from storm damage, and they were an absolute cluster to get resolved as well (one vehicle, one house). Some how, up until about 3 years ago, her parents were still loyal to NRMA too, and we were like "How the hell are you so loyal to staying with them, when other places are so much cheaper, and they've f**ked you over every time you've ever had to make a claim?"
    • I got the four AN10 fitting welded up to the cam covers and started up making the head to sump breather/drain lines. The front passenger side cover I used a 45 up top and a 90 at the bottom into the stock VCT head drain spot (3/4" BPST to AN10 adapter) thats unused on the RB25DET NEO with some speedflow flame shield to protect it from the manifolds heat.   back passenger side was a 90 up top with some flame shield and 45 at the sump end. The rear drivers is 45 at both ends   the front drivers fitting is capped off for now but ready to go if i want to try moving the breathers around. I was told by the fabricator to leave all the welds raw for now to make sure there are no pin hole leaks. A lot of cleaning up, re bundling looms and degreasing to go as well as final assembly on the cam cover baffles. The first real test will be 28th March at a Circuit event. added complexity and more spots for leaks but overall looks relatively neat imo
    • Yeah i think the dash needs to come out. To get the loom or maybe just climate control and radio cluster. My mirrors are done i think the motors don’t work so well after flood haha i need the ac fan, you said you wanted to keep it for your 31 and interior loom not including boot. The wiper motor. I’m not sure how good the window surrounds are on the exterior on the pintara.  I will message you to get your bank details shortly 
    • Just another barrier put up to stop cars being modified. When we're all driving Chinese sewing machines, you won't want to modify it anyway, and you'll likely already have slashed your wrists and be locked up in a padded room for your own protection.
×
×
  • Create New...