Jump to content
SAU Community

Recommended Posts

Y'day after work went to start my car after is had been sitting for 8 hours, I turned the key it started but is strugled to build revs to idle (900rpm) the rpm's went up in stages 200rpm 500rpm then finally when i touched the accelarater it went up to 900rpm? i thought oil pressure? or something to do with cold start?

the only thing i touched was the afm all i did to that was make sure the plug was in properly

i have another question aswell, i think my afm is playing up my car just doesn't feel the same since last fri nite when i had a major boost cut, it was like a hit a wall then i took my foot off the accelerater abit it started to boost again! now it feels different, could it be in some kind of limp mode? it still revs past 3000rpm just feels a bit slower

is there a way to check the afm is working 100%? with afm do they either work or not work? or can they still work at only 50% if that make sense

thanks

if stock ecu, get nissan consult (cable and software) you can buy it, check for NewKleer (he makes them) on the forums

then check the stock ecu diagnostics via the software it will tell you if the AFM is toast

if AFM is toast - ie completely dead REV is capped at 2500rpm

but if its dirty / mangled it may work enough to run, but make fuel injection run like ass, ie botched airflow vs real airflow

check its plug, check for damage, visual inspection, check with elec/carby cleaner

Do a search, from what you are saying the airflow meter has dry solder joints inside on the board. There is a how to for repair if you do a search. As a temp solution you could possibly cable-tie the wires down tight one way or the other but it needs to be fixed or replaced.

have you put diffrent fuel in latley???

sounds like it is fueling up.. could be your afm or your fpr......

if its a stock ecu, do a reset and put it in learn mode....

to reset Take the terminals off the battery, then turn the lights on to get rid of stored power.....

put back together and turn the key... it will be in learn mode for 30 key turns... if it was your fuel it will sort it self out.... if its ur afm, clean and replace if you have tooo...

good luck

also check your plugs.... could have givven you the wall hitting experience.. and be down on power..

thanks muff i will try anything is there a way to check voltage with a multimeter for the afm?

im waiting on new coil packs i will check and change plugs when i get the new coils

and for the fuel i use the same fuel from the same place everytime i fill up

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...