Jump to content
SAU Community

Recommended Posts

Hi all,

Can anyone please confirm when hi beams are switched on, the low beam headlights should also remain on?

This is what the mechanic reckons as I have just gone for a pink slip test and did not pass because of this.

From memory I have never seen happen on my R33 GTS-t but haven't really took too much notice.

Cheers,

Leo

Edited by gwholxc
Link to comment
https://www.sau.com.au/forums/topic/317977-help-regarding-headlights-for-r33/
Share on other sites

Hi all,

Can anyone please confirm when hi beams are switched on, the low beam headlights should also remain on?

This is what the mechanic reckons as I have just gone for a pink slip test and did not pass because of this.

From memory I have never seen happen on my R33 GTS-t but haven't really took too much notice.

Cheers,

Leo

The low beams turn off when you put high beams on as standard. I would find a different mechanic...

If you try and hold the stalk between the low beam and high positions can get them working at the same time though :blink:

Legaly your mechanic is correct. Skyline headlights don't do this and most people couldn't give two shits so just find a different mechanic.

affirmative. almost all cars that you see will have both highs and lows on at the same time. r33s all have what you do. there is a mod you can do, and its in the DIY section to fix this.

affirmative. almost all cars that you see will have both highs and lows on at the same time. r33s all have what you do. there is a mod you can do, and its in the DIY section to fix this.

I only noticed it as something out of the ordinary when I got my Subaru, low beams are always on!

I wonder what reasoning behind the rule is... as the high beams ALWAYS come on before the low beams turn off so you always have continuous forward facing light and the low beams are quite redundant while the high beams are on :blush:

Makes sense for the low beam to stay on when turning on high beam if you've got xenons... it's not good for the xenon bulb to be turned on and off quickly. But otherwise agree if they're just standard halogens the low beam is made redundant

I'll check out the DIY section; I've wanted to have this done since buying series 3 headlights aftermarket.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dunno what to tell you, when I look at it on Consult I can see this warmup timing map kicking in around 40C coolant temp and it sticks around for a while:  At part throttle on the normal base timing map it peaks around ~43 degrees of timing or something like that, this warmup timing map drops it to like 12-15 degrees. 
    • I don't think that's what you're seeing. Something else doing that. The only time I've seen it get so retarded is when it's trying to control idle (in which case we're not talking about mapped timing tagets anyway) and when there is an extreme coolant temperature sensor fault. The RB26 ECU is essentially the same as the 20 ECU and I knew that ging inside out. There is no facility for it to retard that heavily on cold start. The OEMs never used to do it back then. I mean, shit, the catalyst is abotu 3 miles down the exhaust anyway. Early light-off was just a twinkle in some EPA arsehole's eye back then, not a regular engine control strategy.
    • I must preface my comments with a general expression of ignorance. I have no specific knowledge of these NA automtaic things. I can only assume that the "steering wheel button" is for enabling the tiptronic controls. Wierd that it would even need/want a button for that... But anyway.... Was the car previously tiptronic? Did you put a new cluster in as part of all this?
    • Regardless, it doesn't seem wise especially on RBs to actually chase MBT. Timing scatter is the big one on stock CAS, even if that's fixed overshoot is worse than undershoot. 
    • It's all about reducing the overall output. Reduce the source of it, you have wayyyy less to deal with in every other step and trick you play with. It's why something like a modern vehicle, so VW, Audi etc, there's thousands of tables for the ECU to calculate what it should be doing with the engine.   Why would you NOT reduce emissions the most effective way possible, when it has very minimal tradeoff, AND manufacturers are always struggling to meet the current standards.
×
×
  • Create New...