Jump to content
SAU Community

Recommended Posts

I had heard it was load related but I don't understand what that means... don't a certain amount of revs mean a certain amount of air is flowing in and out of the engine (hence spooling up the turbo), loaded up or not?

I was asking b/c I was talking to a mate about why auto's are better than manuals and he said that the stall converter in an auto allows boost from launch (true)

Link to comment
https://www.sau.com.au/forums/topic/31832-boost-in-neutral/#findComment-641119
Share on other sites

I think this is how it works:

The computer will dump in more full under different load point on the fuel map. Therefore when you are in neutral there is no load on the engine so not as much fuel therefore not as much exaust to spool up the turbo...

Launch control on the other hand retards the ignition so the fuel gathers and explodes in the exaust manifold with creates the flow to spool up the turbo...

Correct me if iam wrong...

Link to comment
https://www.sau.com.au/forums/topic/31832-boost-in-neutral/#findComment-641123
Share on other sites

Retarded ignition means that the combustion has less chance of doing useful work, so it will either burn at the bottom part of the compression stroke or once the exhaust valve opens. I've heard that retarded timing can burn your valves, but probably only on older engines.. But yes, retarded timing means a given fuel/air mixture is doing less useful work on the engine and therefore you can use more air/fuel to run at the same point (which is fine if you are in neutral and want your turbo spinning, but useless if you want to accelerate).

Link to comment
https://www.sau.com.au/forums/topic/31832-boost-in-neutral/#findComment-641170
Share on other sites

JIMX

"I can get plenty sideways without boost and fat 255 tyres :) Of course boost picking up soon after launch helps it stay sideways, but I've never needed it off the mark."

well as soon as the clutch is droped there is Load...... Thus boost!

thats if the clutched is droped when the rpms are at a good level!

Link to comment
https://www.sau.com.au/forums/topic/31832-boost-in-neutral/#findComment-641362
Share on other sites

Well if you give it a quick rev you will generate boost as the engines temporary loaded accelerating its own rotating mass, but thats very short, so thats why you hear the bov when you give it a quick stab... which can make you launch abit harder if you time it right... autos have boost because of the resistance/load from the torque converter...

I know of a few conversions where a rb20det turbo and manifold has been fitted to a rb25de (changed ecu and injectors obviously) and that made boost at idle.... looks weird when you go to take it for a test drive and the gauge is sitting at 5psi while its just idling away...

Link to comment
https://www.sau.com.au/forums/topic/31832-boost-in-neutral/#findComment-641510
Share on other sites

you just said that you can get plenty sideways without boost!!

just commenting that most likley it is With boost!

 

cheers:)

Oh :) Well, the initial wheel spin happens without boost, and I daresay it wouldn't really need boost to continue (although boost makes it easier). So although I am getting boost by a certain stage, I doubt it's absolutely required.

Any NA SKyline owners want to confirm or deny that?

Link to comment
https://www.sau.com.au/forums/topic/31832-boost-in-neutral/#findComment-642282
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...