Jump to content
SAU Community

Recommended Posts

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

Link to comment
https://www.sau.com.au/forums/topic/318658-r32-starts-to-die-when-idling/
Share on other sites

Hey mate just wondering if you have a blow off valve, because i had this problem and spent s##t loads trying to find the problem. Changed mine back to stock runs like a dream.

hey yeah i do, but the car was fine before with the blow off valve, and then it just started dying like one in a week then twice, and now its always everyday at least 5 6 times. Should i check the blow off valve? or the boost control or something???

couple things could be causing your problem

1/ try to tighten the spring on the blow off valve might be too loose and leaking at idle causing stalling

2/ throttle position sensor is sitting in the wrong position if you rev it in neutral let the throttle drop and it dies could be a good chance its not set up properly

3/ air flow meter clean and check

4/ a fuel leak at the injectors or metal fuel filter anywhere along the line can cause stalling and idle issues

5/ your engine should idle around 800rpm adjustments to the ecu idle control the aac (idle valve) located on plenum and throttle position sensor need to be made correctly if ones out they are all out.

these would be your main causes of stalling

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

I had the exact same problem with mine. I checked all the usual suspects and it turned out to be a faulty Oxygen Sensor. To test: Warm car up by leaving to idle in driveway. When idle starts to fluctuate unplug the wires going to the Oxygen Sensor (located on dump pipe behind turbo). Leave for a minute and see if your idle picks up. If it does your Oxygen Sensor needs replacing.

From experience, all these RB engines suffer from this as the mamagement system wasnt designed that well for hotter climates and dont allow for "ageing" of the parts. Particularly the AAC valve clogs up and in hindsite Nissan should have made this valve a bit bigger so it takes over more "control" of the idle. This is why a good clean of this valve helps. I have installed a small bypass valve into mine connected to the air conditioner compressor clutch, so when the extra load is on (air con running) which sometimes stalls the engine on a hot day at the traffic lights, the extra air going in helps pick up the idle speed. A small solenoid valve with 1/4 inch air lines does the trick. wire it up in parrallel with the air con clutch wire.

The IAC valve on most engines seems to have stopped working, not sure why, but i just closed mine off and screw out the idle adjust screw a bit to compensate, means i have a slightly higher idle than usual, but the ecu compensates for this with the AAC valve slightly and with this setup, it usually hasnt a issue.

Its just a bit of a pain with these engines the idle setup, not the best. In later models they made the ecu use advance and retard idle control a bit more aggressive to take more control and prevent stalling. If you have a good look at a unmodified R34 engine you will notice how much better they idle.

The early R32 2 litre engines were the worst ones for this problem.

You just have to fiddle with them a bit and maybe put up with a bit higher than normal idle and you can live with it!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not noticeably. Arguably, the catless turbo is going to work harder in a different direction, as it will spool up faster, go to higher speeds more easily. Only if it was tuned in the original condition. If it was a stock tune, using the AFM before and after the cat/dump change, then no, no retune needed. If the car is running on a MAP sensor, then it might well benefit from a retune. It might even run a little dangerously without a retune, but it could quite easily be fine.
    • We had this blend that uses 98RON + 10% Ethanol which brought it to 100RON. It's no longer available anymore unfortunately.
    • Does it make a difference in your turbo having a shorter life if you have a cat converter as it causes that back pressure versus less/no back pressure with a decat? (Not sure if this is accurate) Also slightly different question if you went from a oem cat to a decat or vice versa will it require a tune? I heard if you change the dump pipe onwards it requires a tune?
    • No. Have only gotten as far as contemplating the task of having to put in the required fairly heavy wiring and fusing to run it (along with the big alternator), and preferring not to. But otherwise, it would be nice to have a little extra freedom as to exactly where the compressor is located and free up some space around the exhaust side of the engine.
    • Following from this in a related by not closely-related sense... Because I was buying a bunch of other GKTech stuff, I got some rear subframe collars. The history that leads up to this is: 25+ years ago the car arrived into the country with stock subframe bushes. At some point shortly thereafter I added Whiteline pineapple rings, set up neutral, and it improved the rear end behaviour. Well, it is my vague memory that I was happier with it with them in. Less axle tramp on launches, generally better, etc etc. ~2012 it got a new non-HICAS subframe with new stock bushes. No pineapple rings. I reckon that ever since then I've been dissatisfied with the axle tramp. Recently I've been f**king around a lot with all aspects of the suspension. One contemplation has been to relocate the rear lower control arm front mount points (and do the other things needed to make that work) to improve longitudinal rear grip by getting rid of some of the stupid anti-squat that Nissan ladled into the R32. But.... before doing that I thought I'd put some collars in. And.... The collars are good. The rear sounds a little bit different, but there has been no significant increase in NVH coming up into the body. In terms of rear behaviour - expansion joints on long sweeping elevated freeway ramps that would sometimes cause the rear to jiggle around a bit, no longer seem to do so. It appears that jamming chunks of metal into the gaps in the rubber so they can't move much is a really good thing. And the launch behaviour and general forward traction situation seems to be greatly improved too. It's impossible to be really sure, because the tyres are completely shagged - they are freakishly willing to let go right now. But as an A-B test with the same tyres it certainly seems to grip up a lot better. Highly recommended to anyone who still has stock bushes.
×
×
  • Create New...