Jump to content
SAU Community

Recommended Posts

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

Link to comment
https://www.sau.com.au/forums/topic/318658-r32-starts-to-die-when-idling/
Share on other sites

Hey mate just wondering if you have a blow off valve, because i had this problem and spent s##t loads trying to find the problem. Changed mine back to stock runs like a dream.

hey yeah i do, but the car was fine before with the blow off valve, and then it just started dying like one in a week then twice, and now its always everyday at least 5 6 times. Should i check the blow off valve? or the boost control or something???

couple things could be causing your problem

1/ try to tighten the spring on the blow off valve might be too loose and leaking at idle causing stalling

2/ throttle position sensor is sitting in the wrong position if you rev it in neutral let the throttle drop and it dies could be a good chance its not set up properly

3/ air flow meter clean and check

4/ a fuel leak at the injectors or metal fuel filter anywhere along the line can cause stalling and idle issues

5/ your engine should idle around 800rpm adjustments to the ecu idle control the aac (idle valve) located on plenum and throttle position sensor need to be made correctly if ones out they are all out.

these would be your main causes of stalling

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

I had the exact same problem with mine. I checked all the usual suspects and it turned out to be a faulty Oxygen Sensor. To test: Warm car up by leaving to idle in driveway. When idle starts to fluctuate unplug the wires going to the Oxygen Sensor (located on dump pipe behind turbo). Leave for a minute and see if your idle picks up. If it does your Oxygen Sensor needs replacing.

From experience, all these RB engines suffer from this as the mamagement system wasnt designed that well for hotter climates and dont allow for "ageing" of the parts. Particularly the AAC valve clogs up and in hindsite Nissan should have made this valve a bit bigger so it takes over more "control" of the idle. This is why a good clean of this valve helps. I have installed a small bypass valve into mine connected to the air conditioner compressor clutch, so when the extra load is on (air con running) which sometimes stalls the engine on a hot day at the traffic lights, the extra air going in helps pick up the idle speed. A small solenoid valve with 1/4 inch air lines does the trick. wire it up in parrallel with the air con clutch wire.

The IAC valve on most engines seems to have stopped working, not sure why, but i just closed mine off and screw out the idle adjust screw a bit to compensate, means i have a slightly higher idle than usual, but the ecu compensates for this with the AAC valve slightly and with this setup, it usually hasnt a issue.

Its just a bit of a pain with these engines the idle setup, not the best. In later models they made the ecu use advance and retard idle control a bit more aggressive to take more control and prevent stalling. If you have a good look at a unmodified R34 engine you will notice how much better they idle.

The early R32 2 litre engines were the worst ones for this problem.

You just have to fiddle with them a bit and maybe put up with a bit higher than normal idle and you can live with it!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
    • You talking about the ones in the photo above? I guess that could make sense. Fixed (but flexible) line from the point up above down to the hubcap thingo, with a rotating air seal thingo. Then fixed (but also still likely flexible) line from the "other side" of the transfer in the hub cap thingo up to the valve stem on the rim. A horrible cludge, but something that could be done. I'd bet on the Unimog version being fed through from the back, as part of the axle assembly, without the need for the vulnerable lines out to the sides. It's amazing what you can do when you have an idea that is not quite impossible. Nearly impossible, but not quite.
×
×
  • Create New...