Jump to content
SAU Community

Recommended Posts

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

Link to comment
https://www.sau.com.au/forums/topic/318658-r32-starts-to-die-when-idling/
Share on other sites

Hey mate just wondering if you have a blow off valve, because i had this problem and spent s##t loads trying to find the problem. Changed mine back to stock runs like a dream.

hey yeah i do, but the car was fine before with the blow off valve, and then it just started dying like one in a week then twice, and now its always everyday at least 5 6 times. Should i check the blow off valve? or the boost control or something???

couple things could be causing your problem

1/ try to tighten the spring on the blow off valve might be too loose and leaking at idle causing stalling

2/ throttle position sensor is sitting in the wrong position if you rev it in neutral let the throttle drop and it dies could be a good chance its not set up properly

3/ air flow meter clean and check

4/ a fuel leak at the injectors or metal fuel filter anywhere along the line can cause stalling and idle issues

5/ your engine should idle around 800rpm adjustments to the ecu idle control the aac (idle valve) located on plenum and throttle position sensor need to be made correctly if ones out they are all out.

these would be your main causes of stalling

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

I had the exact same problem with mine. I checked all the usual suspects and it turned out to be a faulty Oxygen Sensor. To test: Warm car up by leaving to idle in driveway. When idle starts to fluctuate unplug the wires going to the Oxygen Sensor (located on dump pipe behind turbo). Leave for a minute and see if your idle picks up. If it does your Oxygen Sensor needs replacing.

From experience, all these RB engines suffer from this as the mamagement system wasnt designed that well for hotter climates and dont allow for "ageing" of the parts. Particularly the AAC valve clogs up and in hindsite Nissan should have made this valve a bit bigger so it takes over more "control" of the idle. This is why a good clean of this valve helps. I have installed a small bypass valve into mine connected to the air conditioner compressor clutch, so when the extra load is on (air con running) which sometimes stalls the engine on a hot day at the traffic lights, the extra air going in helps pick up the idle speed. A small solenoid valve with 1/4 inch air lines does the trick. wire it up in parrallel with the air con clutch wire.

The IAC valve on most engines seems to have stopped working, not sure why, but i just closed mine off and screw out the idle adjust screw a bit to compensate, means i have a slightly higher idle than usual, but the ecu compensates for this with the AAC valve slightly and with this setup, it usually hasnt a issue.

Its just a bit of a pain with these engines the idle setup, not the best. In later models they made the ecu use advance and retard idle control a bit more aggressive to take more control and prevent stalling. If you have a good look at a unmodified R34 engine you will notice how much better they idle.

The early R32 2 litre engines were the worst ones for this problem.

You just have to fiddle with them a bit and maybe put up with a bit higher than normal idle and you can live with it!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So where is this message group so we can organise another meet? Keen to come along and catchup. Might eventually be in a skyline again next year, but the Mustang will have to do for now. Also need to get the WRX back on the road. Stupid f**king money pit that thing is.
    • Stock equivalent turbo replacement is a bit of a nightmare. The old Hitachi ceramic things were pretty good for their time, but they have primitive, vintage aerodynamics. The only thing they have going for them is a light turbine**, and there are plenty of other light turbine options these days, in both materials and CNC manufacturing methods. So, the old stocker makes absolutely no power at all compared to its physical size and its (not very low) boost threshold and response. ** and the ONLY thing that was good about the ceramic turbine was that it was light. In all other respects it is a nightmare. To get a turbo that is anywhere near equivalent in terms of power capacity (ie, to avoid it being "bigger" and needing tuning/fuelling/etc) you have to physically downsize. And that is not a "stockish" replacement. Doesn't just fit where the old one did. At least a frame size down, probably need a new dump, probably need new inlet and outlet piping made on the compressor side, new hose connections as D said above. I say, if you have to suffer that much work, you might as well do the same work to fit an even bigger (than stock) turbo, have more power (and hence have to do injectors, ECU, etc), and love life, instead of suffering with stock power levels. Or, you get a light highflow from someone like Hypergear. A highflow that has not been pushed too far from stock. There are still modification consequences here though. HG's cores are smaller than the massive Hitachi core, so it is shorter, moves the compressor housing backwards and requires mods to the air side piping. Plus new hoses. Looks stock, mostly fits where the stock one did (with the previous caveats mentioned), makes a bit more power but can be run at stock boost levels and not cause too many ECU problems. But, seriously. It's 2024. Like - 25 years since the R33 came out. It's time to put an ECU in it. I Nistuned my car (on RB20 ECU then later again on the Neo ECU) and it was the single best thing possible for minimal money. Dial out the R&R bullshit, fix up the fuelling and timing to make it more efficient for normal driving (cut fuel consumption by >10%). Nistune is not an option for you unless you change the ECU, so you might as well just do a standalone. it will be worth it. And then you can tune it up to the limits of the injectors and AFM, which is pushing 200rwkW and enjoy some actual squirt, instead of the lazy barge-like motion you get from a stock engine, turbo and management.
    • He can't post pics until he's at 10 post count.
    • Welcome James.....will be interesting to see how much fun there is in the project. .....where's the pics?
×
×
  • Create New...