Jump to content
SAU Community

Recommended Posts

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

Link to comment
https://www.sau.com.au/forums/topic/318658-r32-starts-to-die-when-idling/
Share on other sites

Hey mate just wondering if you have a blow off valve, because i had this problem and spent s##t loads trying to find the problem. Changed mine back to stock runs like a dream.

hey yeah i do, but the car was fine before with the blow off valve, and then it just started dying like one in a week then twice, and now its always everyday at least 5 6 times. Should i check the blow off valve? or the boost control or something???

couple things could be causing your problem

1/ try to tighten the spring on the blow off valve might be too loose and leaking at idle causing stalling

2/ throttle position sensor is sitting in the wrong position if you rev it in neutral let the throttle drop and it dies could be a good chance its not set up properly

3/ air flow meter clean and check

4/ a fuel leak at the injectors or metal fuel filter anywhere along the line can cause stalling and idle issues

5/ your engine should idle around 800rpm adjustments to the ecu idle control the aac (idle valve) located on plenum and throttle position sensor need to be made correctly if ones out they are all out.

these would be your main causes of stalling

this didnt use to be a big problem but now has gotten worse.

i would be driving normal and then stop at the stop lights and then all of a sudden the revs usually once u put it in neutral the revs jump to like 1500rpm and then they come down to about 1000rpm and then it just holds itself there, mine doesnt, it jumps up as normal to 1500 and then it goes down to 1000, then lower lower lower, until it hits 0 and then switches off.

everything i stop somewhere idling i have to keep revving the car to keep the revs up or else it i left it it would just die out. this happens when i stop quick when i quickly shift into neutral whilst driving it jumps to 1500 then bang down to 0, but if i stop realllyy slowing and slow down before i go in neutral it doesnt have a big affect, only when i stop quickly or normally, i dont wanna have to slow down and then creep 500 metres before a stop light i dont know whats going on with my car!!!

i thought it was the air, but i checked everything all the air pipes the little cords that go to everything, its all locked in and even if it was a air problem the car would continuously revving up and down at every stop this only happens 80% of the time, but its a shit wen it happens on a hill lol

what do you think it could be?

I had the exact same problem with mine. I checked all the usual suspects and it turned out to be a faulty Oxygen Sensor. To test: Warm car up by leaving to idle in driveway. When idle starts to fluctuate unplug the wires going to the Oxygen Sensor (located on dump pipe behind turbo). Leave for a minute and see if your idle picks up. If it does your Oxygen Sensor needs replacing.

From experience, all these RB engines suffer from this as the mamagement system wasnt designed that well for hotter climates and dont allow for "ageing" of the parts. Particularly the AAC valve clogs up and in hindsite Nissan should have made this valve a bit bigger so it takes over more "control" of the idle. This is why a good clean of this valve helps. I have installed a small bypass valve into mine connected to the air conditioner compressor clutch, so when the extra load is on (air con running) which sometimes stalls the engine on a hot day at the traffic lights, the extra air going in helps pick up the idle speed. A small solenoid valve with 1/4 inch air lines does the trick. wire it up in parrallel with the air con clutch wire.

The IAC valve on most engines seems to have stopped working, not sure why, but i just closed mine off and screw out the idle adjust screw a bit to compensate, means i have a slightly higher idle than usual, but the ecu compensates for this with the AAC valve slightly and with this setup, it usually hasnt a issue.

Its just a bit of a pain with these engines the idle setup, not the best. In later models they made the ecu use advance and retard idle control a bit more aggressive to take more control and prevent stalling. If you have a good look at a unmodified R34 engine you will notice how much better they idle.

The early R32 2 litre engines were the worst ones for this problem.

You just have to fiddle with them a bit and maybe put up with a bit higher than normal idle and you can live with it!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: Tunehouse looked into the problem and identified a wiring issue between the camera unit and the connector. They managed to get it working , but did warn me at some point it will stop working again. From their perspective it is unserviceable and will need replacement. They did some research and found that the new replacement camera would be Approx $1400 supply only (their fitting cost would be $190) . They did provide the part number (28442-JL05B) and a quick google of the part number shows that these are rather expensive brand new (seemingly no longer in manufacture) for the places that still have them in stock, with the used option potentially presenting  the same issue down the track at some unknown point. They are happy for me to supply the part so that they can fit it. Decisions, decisions... I can definitely recommend Tunehouse (thankyou Vee37!). Cost for the diagnosis was as quoted  ($190) , car was ready on time and communication was top notch. Their workshop is super clean and modern, and there was plenty of car candy parked out the front on the day I went.   Would definitely go back.   
    • to fix the voltage drop issue I swapped out the old 150amp alternator which turns out is a brand known for having issues and replaced it with the black 180amp alternator beside it 
    • For anyone interested, the Way Back Machine has that Japanese website archived with pictures, etc: https://web.archive.org/web/20051023225805fw_/http://www.a31cefiro.com/air_con.htm "Simply swapping the wiring of the harness will not allow it to function properly. For the outdoor air sensor and sunlight sensor, disconnect the wiring connected to CN1-11 of the air conditioning harness from the harness and connect the sensor side wiring to earth. For the indoor air sensor, disconnect the wiring connected to CN2-3 of the air conditioning harness from the harness and connect the sensor side wiring to earth. The connector PIN numbers listed here are the genuine A31 PIN numbers. To avoid incorrect wiring, check with a tester before wiring. Also, disconnect the wiring in a location close to the sensor. The disconnected harness side wiring will not be used, so be sure to insulate it." Wish someone sold a conversion harness to just plug-and-play a Kouki 180sx digital climate control into C33/A31. I'm decent with wiring but feeling kinda lazy about taking this on. Edit: Did some more digging and found a helpful Minkara blog post about the conversion as well: https://minkara.carview.co.jp/userid/1831116/car/1360568/2284209/note.aspx "After installation is complete or the battery is replaced, you need to go into self-diagnosis mode and set the internal air recirculation. The way to do it is to "hold OFF with the key on for more than 5 seconds, set the number to 5, then press 卍→C." ↑↑↑It probably won't make sense unless you actually try it (・∀・)." Lol wtf
    • Maybe SAUNSW could see howany members would do a motorkhana day if Schofield's is still available for a reasonable price...
    • Skip the concrete, we just need to smooth a field. Mark knows how to drive a grader Duncan   I reckon 100x100 flat area for skid pan style, and then some sort tracks for rally... Duncan's already got a rally car on the premises to...
×
×
  • Create New...