Jump to content
SAU Community

Recommended Posts

Hey everyone,

Up for sale is my R33 S1 Skyline. Has just recently been involved in a hit and run :D

Was meaning to sell the car earlier as I now have a company car but just hadn't come around to it yet.

Overview:

  • 5 Speed Manual
  • RB25DE (non turbo) - perfect for P-platers
  • Gearbox and clutch in good condition - no crunching or slipping
  • 18" 2 piece rims
  • Lowered springs
  • Full 2.5" exhaust system to dual tip - fitted by Bankstown Muffler Fit. Nice deep tone, not been pulled over for it once.
  • Momo Steering Wheel
  • Recently had Harmonic Balancer, Key Ways and Crank Shaft replaced
  • Brand New Century Heavy Duty Battery
  • Rego until 02/2011

- Due to the hit and run, a new front bar and reo will be needed. I have a replacement front bar is 2 tone grey that just needs to be painted so all you need is a reo to fit.

- No damage to the chassis or radiator support from the hit and run and is not on REVS

- Previous damage to drivers side rear quarter has been there since I bought the car.

- Paint is in ok condition, fading on driver side fender and boot.

- Odometer reads "220,000" kms but the car has travelled 168,xxx km before replacing the cluster as the needles stopped moving.

Price: $6k or $5.3k without rego. Also interested with swaps for S13 or 180sx only

Pictures: to come.. I am currently capped and takes ages to upload photos :cool:

Contact: Reply to thread, PM or contact 0431 737 515 to organise inspection

Car is located in Sydney, Parramatta area

Link to comment
https://www.sau.com.au/forums/topic/318749-black-1993-r33-skyline-gts/
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have one and it was at ~43.5PSI.
    • Put a pressure gauge on the fuel rail.
    • I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
×
×
  • Create New...