Jump to content
SAU Community

Recommended Posts

Hey, Im sorry if this sounds like a really stupid question that anyone with a license should know, but I have just never been sure.

When your tyres say 55PSI Max press, does that mean it would be best for me to fill it to 55? Or does it mean thats just the max it can handle, but I should be putting in 50?

Or am I way off and theres an ideal PSI such as 43 for certain sizes or something like that?

I know your tyre pressure has an affect on petrol consumption, but im also told that your tyre pressure can have a HUGE impact on your speed and acceleration, so I was wondering about all this.

Thanks for any answers

Link to comment
https://www.sau.com.au/forums/topic/318811-max-psi/
Share on other sites

they're just the stock tyres, so im gonna assume the figures that cancer gave were right under that assumption?

I was recommended 38-40psi on 235/45/17 if that helps, 40psi was for an advanced driving course at Sandown, but everyone seems to recommend a slightly different amount so you will have to experiment :P

Link to comment
https://www.sau.com.au/forums/topic/318811-max-psi/#findComment-5211170
Share on other sites

Experiment mate, but always gauge it on the tyre profile rather than wheel size.

With standard tyres anywhere from 32-36 will be fine. Low profile (35/40) anywhere from 38-44 is not uncommon.

When you get to know more about it, you will use different pressures for different situations. A good test you can do is to inspect the tyre wear after some time...if you have too much wear on the sides of the tread it means your pressures are to low, too much wear on the centre of the tread and your pressures are too high.

Link to comment
https://www.sau.com.au/forums/topic/318811-max-psi/#findComment-5211364
Share on other sites

There is quite a bit of info on this around the web, a lot of people state the best tyre pressure for your tyres in terms of performance, wear and comfort is the MAX pressure stated on the sidewall of the tyre minus 10%. So under that assumption it would be 55 - 5.5 which is 49.5PSI. That seems a bit high for me, I would stick to between 36-40 PSI cold pressure.

Link to comment
https://www.sau.com.au/forums/topic/318811-max-psi/#findComment-5221250
Share on other sites

WOW!

Are you guys serious?

I run 45-50psi on the rears at the track when I go drifting.

And about 32-34 at the front

(16" rim, 205-55)

It depends very greatly what press to run.

Factors like wheel alignment, driving style, driving conditions, quality of rubber and what you want to get out of your rubber.

Have a look at the tyre wear on the rubber, where is it wearing first? Is it an even wear? Is it feathering on the tread blocks?

For daily driving I wouldnt recommend more than 36 just to try limit fuel consumption.

Tyre press is a comprimise betwee grip and tyre wear. Do you want you rubber to last? or do you want it to grip?

Link to comment
https://www.sau.com.au/forums/topic/318811-max-psi/#findComment-5223024
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...