Jump to content
SAU Community

Insurance - Shipping & Handling


Recommended Posts

I'm looking to import a V35 Coupe and was wondering what peoples thoughts are on insurance, and for that matter what options are available. There are, I think, four stages to potentially cover before you can obtain normal car insurance;

  1. From purchase (auction, dealer) to port / loading on ship.
  2. Shipping from Japan to Australia.
  3. Unloading / storing at Aussie port.
  4. Picking up and delivering to Compliance / Home (this step could possibly be covered by normal car insurance? Although the car would not be roadworthy at this point)

Is it possible to insure end to end? Do people normally bother or do most just wear the risk?

What would you do?

Link to comment
Share on other sites

If you're importing through a broker, they should be able to help you with the first 2.

For 3 and 4 you may be able to get something like laid up insurance. I know Shannons do it for their custs. Pretty much covers the car while being stored and transported on the back of a truck.

No one will cover you though will its unregistered if its being driven on the road. Not that i could find anyway. I actually drove mine from the compliance place to home to RTA which you can do, just can't remember having insurance for it whilst doing that.

Link to comment
Share on other sites

I'm looking to import a V35 Coupe and was wondering what peoples thoughts are on insurance, and for that matter what options are available. There are, I think, four stages to potentially cover before you can obtain normal car insurance;

  1. From purchase (auction, dealer) to port / loading on ship.
  2. Shipping from Japan to Australia.
  3. Unloading / storing at Aussie port.
  4. Picking up and delivering to Compliance / Home (this step could possibly be covered by normal car insurance? Although the car would not be roadworthy at this point)

Is it possible to insure end to end? Do people normally bother or do most just wear the risk?

What would you do?

1, never done it, never needed it and not sure it's actually possible at all. I've never heard of it.

2, I used to do it, now I just use good shipping companies instead and never have a problem. if the car is super duper special I'd spend the extra money on putting it in a container rather than buying some dodgy insurance. prevention is far better than the cure. I'd much rather make sure nothing happens to the car up front (as best I can) than have to bother with insurance claims down the track.

3, same as above. the car is unloaded and will be at the port for a couple of days only. it's secure in there and nothing will happen. not worth it.

4, for this one I would get regular comprehensive insurance. tell the company you've bought a new car and it will be in your possession as of XX date but is not yet registered. it shouldn't be a problem, just give them the chassis number.

end to end I've never heard of anyone who has insured a car from the moment it was purchased at auction right through to it being complied and registered in aus. it certainly doesn't keep me awake at night....

edit: dude! just saw you are buying a V35 coupe. seriously it's not worth it. it's a car that costs a bit over $10K to buy. waste of money insuring that or putting it in a container. seriously even for cars $100K+ carefully monitored, regular roro shipping process is fine.

Link to comment
Share on other sites

You probably cant get insurance for the car from the auction to the port, but at each stage, when the car changes hands, the car is checked over, and your customs agent in Japan should be able to trace that sort of stuff if something major happened. Same in Aus as well.

Shipping with Kiwi, all cars are insured but doesnt include inner cargo.

I was personally really worried about the process, but after doing it twice now, I havent really had much to worry about. I have heard of horror stories though. You can expect minor things to be taken, I had my gear knob pinched on my first car. And on my Legacy, someone has replaced the rear view mirror with a different one. Quite funny actually, and I prefer the one they put on :yes:

Link to comment
Share on other sites

Guess I won't bother with insurance during transport then, but what if the ship sinks?!

And, when it arrives in Australia I should be able to get it covered by normal car insurance.

To get from the dock to wherever, I believe I can get a temporary permit to drive the car from one location to another (did this with an unlicensed motorbike from local auction recently), is that what most do? I'm guessing I can just drive it home if I need to wait for compliance, then get another permit to drive it to compliance, then home or the pits for licensing. Is there a limit on the number of permits you can get?

Link to comment
Share on other sites

hey Insurey McInsurance. what's with you and insurance?

what if the ship sinks? really?

very very remote chance of that happening... there is higher chance of the ship being boarded by pirates and hijacked

Link to comment
Share on other sites

if the ship sinks you will most likely loose the car and you will be required to pay a share of the salvage cost. you can insure against that salvage cost liability. it's called general average insurance. personally I think it's a waste of time. if it worries you then look into it. it does occasionally happen. a business partner in japan has had a ship sink that he had some cars on. not nice. but that's the only one I know of personally. of the thousands and thousands of voyages per yer carrying cars I would say less than 1 sink.

Link to comment
Share on other sites

If you really want piece of mind, then do it. Its not expensive.

As an example i last used Associated Marine Insurance who are underwriters for Zurich i think. Cost was $230 for $23000 car. Was a 2yr old V35 at the time. If the car is worth less, the premium will come down.

Easy process, get photos of the car before it boards and pay your premium once they give you the quote.

so yeah if no insurance means no sleep, just do it :)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
    • They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
×
×
  • Create New...