Jump to content
SAU Community

Removing Crank Pulley Bolt (27mm)

rich81

By rich81,
in Engines & Forced Induction

 Share

Recommended Posts

rich81 Explorer

rich81

Posted
Posted

Hey guys,

Still tearing down this RB25DET I picked up this week. My next challenge: removing the crank pulley. There's no flywheel on the motor so I can't really shove anything thru the ring gear to hold the crank in place.

So my questions.....

a) what's the thread diameter of the studs that mount the flywheel to the crank? in case I need to frankenstein something up to keep it steady.

b) Am I missing anything with removing that 27mm bolt, other than giving it a good smack with a hammer to crack the seal then just undoing it with the help of a breaker bar etc?

c) Anybody have an ingenious way of securing the other end of the crank, other than by my Frankenstein method above (metal bar with a few holes drilled in to secure it against the crank, then lock it against engine stand)

Thanks guys.

Link to comment
Share on other sites
gfunkk Rising Star

gfunkk

Posted
Posted

be careful man or you could damage the seal behind the crank.

put the flywheel on then use the bolts where the clutch attaches to the flywheel to tie some shit to the engine with

then yea breaker bar..

Link to comment
Share on other sites
rich81 Explorer

rich81

Posted
  • Author
Posted
be careful man or you could damage the seal behind the crank.

put the flywheel on then use the bolts where the clutch attaches to the flywheel to tie some shit to the engine with

then yea breaker bar..

There's the problem tho - I don't have a flywheel, at all.

Thanks for the warning about the crank seal.

Link to comment
Share on other sites
rich81 Explorer

rich81

Posted
  • Author
Posted
rattle gun

*Might* get access to one of those - would it be enough by itself to just crack the bolt straight off? I.e. does an air-powered tool deliver enough force to just break the bolt without needing to secure the other end etc?

Link to comment
Share on other sites
Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
*Might* get access to one of those - would it be enough by itself to just crack the bolt straight off? I.e. does an air-powered tool deliver enough force to just break the bolt without needing to secure the other end etc?

yep...did it twice yesterday with RB26 engines...they were 350ft/lb tensioned. I do have a good rattle gun though but most reasonable quality ones should be enough for a 25.

Link to comment
Share on other sites
rich81 Explorer

rich81

Posted
  • Author
Posted
The engine should provide enough resistance for the impact of the gun to loosen the bolt.

Thanks, THAT'S what I was trying to say :-)

OK, well the missus' old man has an air compressor, so I guess I need to hit up Kennard's for a rattle gun.... I wonder if they hire them out?

Thanks for the advice guys.

Link to comment
Share on other sites
rich81 Explorer

rich81

Posted
  • Author
Posted
If no rattle gun, take the sump off and use rag covered spanner or such to wedge between the crank and block. (use a counterweight)

Great idea - I have a Bag O' Rags and a big-ass spanner. I'll try that before going for a rattle gun - I'll set the wrench up and smack it with my breaker bar.

Link to comment
Share on other sites
Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
If no rattle gun, take the sump off and use rag covered spanner or such to wedge between the crank and block. (use a counterweight)

ahh yes...before i had a rattler i used the wooden handle of an engineers hammer to wedge the counterweight.

Link to comment
Share on other sites
STATUS Grand Master

STATUS

Posted
Posted

yeah wood is the go try not to use anything thats hardened just in case it slips and centre punches something useful :P

Link to comment
Share on other sites
rich81 Explorer

rich81

Posted
  • Author
Posted
the handle of the hammer i mentioned looks like a crocodile has been munching on it...lol

I got the bastard off.

I wedged a piece of wood between the girdle and one of the rod caps at the point where the rod has minimum clearance from the girdle. Then with the timing belt still in place, I was able to undo the intake cam gear bolt and then the crank bolt with surprisingly little force... they didn't just come right off, but instead of the epic battle I was prepared for, I just had to use a measured amount of force with the breaker bar until they came free. Then used a pulley puller to get the harmonic balancer off, and that was that. It's amazing how easy it can be with the right tools (and good advice!). Thanks guys.

Head came off tonight, tomorrow I break apart the bottom end and see what the bearings look like.... :blush:

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Thanks for the reply, So i've continued playing around, and fitted the injector adaptors onto the injector, the fuel rail is not able to be mounted now as the injectors sit a bit further out. I suppose the point of the adaptors is so that the injector nozzle isn't so deep into the intake? I suppose 1mm extra on the o-ring would do it but still can't mount the rail onto the intake haha. Waiting on a reply from Aeroflow I'm sure there's something stupid that I'm missing...
    • defari
      Spotted - QLD Skyline Owners

      By defari · Posted

      EMJ33 or EJM33 - west end
    • TurboTapin
      GReddy Injector Help!

      By TurboTapin · Posted

      I have a radium fuel rail on my Greddy manifold and used the supplied radium fuel injector to manifold adapters (The round green things pictured). I did always wonder if you could just go ahead and use the second lower hole like you're doing... Wouldn't thicker o-rings solve your issue?    
    • MBS206
      Does anybody use the Firestryker or Element sticks?

      By MBS206 · Posted

      From what I've seen and experienced first hand with those powder extinguishers, they're good to use to break a window and escape the car, and half the time then do f**k all to stop a fire. You just need much more than 1KG worth of powder. Not to mention, half the time it's an engine bay fire, and you can't easily, and do not want to completely open the bonnet, so you're left pretending to be an American Infantry... Spray and Pray baby!   And then 100% that shit is really destructive afterwards!   Realistically, those little ones at a race track might help you keep the fire from growing and give the fire marshal / truck a chance to actually get to you with their multiple large bottles.   For a road car, these days, prepare to deboard as quickly as humanly possible, and move to safety. Allow insurance to fix replace it (unless it's like a rare classic etc, then do nearly everything possible to save it!) Keep the little extinguisher with you to help protect other things around you from burning while you stand there singing "How can we sleep while our beds are burning?"   Secondly, powder extinguishers I freaking hate for indoor use, (this isn't really relevant to a car) as you will get a powder fog around you, and it can be disorientating.   When I did fire training when at BlueScope Steel, they have (had?) their own fire brigade on site. We did all the training, and at the end we were told, "If it's an indoor fire, and you need to use a powder extinguisher, we as the fire brigade would rather you just exit the building, you're more likely to get lost in the smoke and powder fog than do much help, so just GTFO" And pretty much that was what they said for most other fires too, grab extinguisher, if it's much more than paper in a bin fire, use extinguisher to get you and others out of the building to safety...   Part of me wishes when my Skyline caught alight many moons ago, I let insurance sort it out, instead of putting the fire out... part of me now says "But I've saved a classic before it was a classic!"
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Hi all,  I have a older model of the Greddy Front facing intake on an RB25DET NEO Head. I've bought aeroflows fuel rail and injector kit (1000cc Bosche injectors) and I'm unsure if the fitment is correct. The injector o-rings fit in the intake hole but it's not snug. I can very easily rotate the injectors even when the fuel rail is mounted. The kit also came with multiple adaptors, they dont make it any more snug and using them raises the injectors up and i cant mount the fuel rail. I hope this makes sense I've asses a few photos.    Thanks so much guys. 
×
×
  • Create New...