Jump to content
SAU Community

Nissan C33 Laurel Rb25det


Recommended Posts

Item Summary: nissan c33 laurel rb25det

Location: QLD: Sunshine Coast

Condition: Used

Reason for Selling: want cash

Asking Price: 11000

Delivery Methods: PickUp

Contact Info:

Extra Information:

Item Summary: nissan laurel 1992 c33

Location: QLD: Brisbane

Condition: Used

Reason for Selling: want cash

price:11,000 o.n.o

Delivery Methods: PickUp

Contact Info: pm me or cal 0406039905

Extra Information:

hey guys sellin my 1992 c33 laurel

1992 c33 laurel

rb25det.. not to sure on ks fresh conversion.

5spd manual

short shifter

exedy 5 puc botton clutch

jjr fuel reg

spitfire coilpacks

gtr fmic

3inch exhaust with drift twin pipes

500hp

k sport coilovers front and rear. 10kg fronts 8kg rears

REAR

camber arms

toe rods

traction rods

front caster arms

extra lock spacers

cusco strut braces front and rear

blits boost oil pressure water temp gauges

deep dish steering wheel

r32 front seats

hand brake drift button

selling with silver metallic paint

getting this painted in next few weeks . then if ive got enough cash getting a tune when my wolf 3d is fixed and goin for 300hp.

post-71323-1273229681_thumb.jpg

post-71323-1273229715_thumb.jpg

Link to comment
Share on other sites

swap for stagea?

link as follows

http://www.carsales.com.au/all-cars/privat...&__Qpb=true

its a long way away,but we can work something out

couple questions

-is it rego'd with the rb25det?

-will it pass a roadworthy? super strict in SA thats all

thanks,will sms you in the morning mate

rodney

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
    • Id like to race in the US i think alot of those track would suit me   For the s15? Youd be stuck between club sprint and the new Open Am wouldnt you depending on how much interior you have left in
×
×
  • Create New...