Jump to content
SAU Community

Recommended Posts

Hi Guys,

Selling my Series 1 R33 Gtst, 1993 model Skyline. I'm the first Australian owner, have had the car for a little over 2 years. Someone backed into the rear quarter, so it still has some damage. Also the drivers door and guard need some paint work. Basically the whole drivers side of the car could do with a respray. The front bar and bonnet need some attention too.

It has roughly 120,000 klms on the clock. I haven't had any mechanical issues with it at all, except for when I first got it the coils needed replacing - runs extremely well.

Registration ran out on 18/05 and I'll be selling it unregistered with no rwc. It shouldn't be too hard to re register, take the boost controller off and the pod filter maybe, that's probably all it needs.

It hasn't had too much work done to it, it has the following mods:

Splitfire Coils

Exhaust from turbo back

R34 side mount intercooler

Pod filter

18' XHP Wheels - tyres around 60% tread. All wheels have gutter rash.

Manual boost controller - pretty much turned down.

Timing belt was replaced with a Gates timing belt at 109,000 klms in September 08. Since then, it has been driven from Sydney to Melbourne and has only travelled 11000 klms including that drive.

It has an Alpine CD & Tape player, with alpine speakers all round including tweeters.

It has the original skyline floor mats

I had bought another boot with drift wing from someone on here, but the fktard couriers dropped it I think ( see photo's). Will include the boot. Also will include the stock R33 side mount intercooler.

There are a couple of cracked hoses in the engine bay - you can probably see my dodgy tape up job. I'll be looking at getting them replaced.

The car hasn't been thrashed, it barely gets driven at all unfortunately.

Looking for $4500 for it. I was quoted about $1000 - $1500 to fix the damage and respray, but that was in Sydney. I don't really have the spare cash or the time to do it, so I've decided to sell it as I need a van for work.

I can be contacted on 0458 333 444 or by PM.

post-60124-1274781280.jpg

post-60124-1274781291.jpg

post-60124-1274781299.jpg

post-60124-1274781305.jpg

post-60124-1274781312.jpg

post-60124-1274781323.jpg

post-60124-1274781334.jpg

post-60124-1274781356.jpg

post-60124-1274781369.jpg

post-60124-1274781381.jpg

post-60124-1274781399.jpg

post-60124-1274781419_thumb.jpg

post-60124-1274781443_thumb.jpg

Hi Guys,

Selling my Series 1 R33 Gtst, 1993 model Skyline. I'm the first Australian owner, have had the car for a little over 2 years. Someone backed into the rear quarter, so it still has some damage. Also the drivers door and guard need some paint work. Basically the whole drivers side of the car could do with a respray. The front bar and bonnet need some attention too.

It has roughly 120,000 klms on the clock. I haven't had any mechanical issues with it at all, except for when I first got it the coils needed replacing - runs extremely well.

Registration ran out on 18/05 and I'll be selling it unregistered with no rwc. It shouldn't be too hard to re register, take the boost controller off and the pod filter maybe, that's probably all it needs.

It hasn't had too much work done to it, it has the following mods:

Splitfire Coils

Exhaust from turbo back

R34 side mount intercooler

Pod filter

18' XHP Wheels - tyres around 60% tread. All wheels have gutter rash.

Manual boost controller - pretty much turned down.

Timing belt was replaced with a Gates timing belt at 109,000 klms in September 08. Since then, it has been driven from Sydney to Melbourne and has only travelled 11000 klms including that drive.

It has an Alpine CD & Tape player, with alpine speakers all round including tweeters.

It has the original skyline floor mats

I had bought another boot with drift wing from someone on here, but the fktard couriers dropped it I think ( see photo's). Will include the boot. Also will include the stock R33 side mount intercooler.

There are a couple of cracked hoses in the engine bay - you can probably see my dodgy tape up job. I'll be looking at getting them replaced.

The car hasn't been thrashed, it barely gets driven at all unfortunately.

Looking for $4500 for it. I was quoted about $1000 - $1500 to fix the damage and respray, but that was in Sydney. I don't really have the spare cash or the time to do it, so I've decided to sell it as I need a van for work.

I can be contacted on 0458 333 444 or by PM.

How much for splitfire coils,

manuel 0406747726

very keen

  • 2 months later...
  • 2 weeks later...
  • 3 years later...

Bump, still trying to get my money back...

This Ben Ellis scammer guy recently logged into one of his aliases - http://www.skylinesaustralia.com/forums/user/60124-extr33me , username "EXTR33ME"

and has since closed down the known facebook page. Would love for karma to catch up with this dude one day....

If you read this Ben, just pay the money back...

$1000.00

BSB: 084-044

A/N: 131739390

This was his car back then - http://www.skylinesaustralia.com/forums/topic/322126-damaged-r33-gtst-series-1-minor-damage-4500/#entry5253936 - perhaps you knew him, or knew of him, or know him...if you do know how to contact him, please encourage him to do the right thing and return the money.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...