Jump to content
SAU Community

Recommended Posts

Ive done a 14.9 1/4, so maybe my 0-100 is around 7. This was done without a spare tyre and front bar and with only a 4000rpm launch. Might do better with a higher rpm launch and better tyres. NA 34s are not built for speed but they are quick enough for me. I only ever managed a 14.4 in my r33 s2 Gts-t, mind u it was pretty stock.

Link to comment
https://www.sau.com.au/forums/topic/32249-r34-na-power/#findComment-654176
Share on other sites

well, having owned both NA cars and an R33 turbo, there's defnitely positives and negatives of NA and forced induction. personally, I'm no speed demon, and almost never drive my R33 in anger, and the NA R34's still look the trick, so I'd prolly go for one of those when the R33 gives up the ghost...

Link to comment
https://www.sau.com.au/forums/topic/32249-r34-na-power/#findComment-654726
Share on other sites

At the moment full exhaust 2.5, pod filter, extractors, safc II. Pretty much extent of things u can do to an N/A. Looking for the 3lt conversion soon, but dont know if ill go ahead with it(its expensive). A friend of mine already had it done and he is happy but cost him more than originally planned (mind u he is in NZ so prob more in Aust). SAFC has so far been the best mod, exhaust and pod were done b4 i got the car. The car ran this time without front bar, rear seat or passenger seat (taken out for a stereo install that i didnt proceed with so also no stereo or speakers at the time), no spare tyre, no jack or tools. So yeah, I honestly dont think that our cars are supposed to be fast but they can be made to be reasonably quick.

HPI did their best time of 7.3 for 0-100 but to be honest with u I dont remember my 0-100 time. So sorry maybe u are right, I just estimated it to be around 7, maybe someone can tell me what a 0-100 time for a 14.9 1/4 mile could be. You have a four door right, just wondering have u weighed your car ? Id like to know just to compare it to mine.

Link to comment
https://www.sau.com.au/forums/topic/32249-r34-na-power/#findComment-655029
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
    • I would strongly suggest using the correct tool. They are not expensive and make the job much easier and don't damage the lock ring. Google "fuel tank lock ring removal tool" to see what I'm talking about. 
×
×
  • Create New...