Jump to content
SAU Community

Need To Drain Current Petrol Any Easy Way Beside Letting It Run Out While Car Is On

boostn0199
 Share

Recommended Posts

N1GTR Grand Master

N1GTR

Posted
Posted

Get a petrol jiggler hose, put the brass end in the tank (of course it will have to be quite long), jiggle it a bit and that will get most out

Then take the line off the fuel reg and turn the key to ON so the pump primes. Repeat. Will take a fair while but it's simple.

N1GTR Grand Master

N1GTR

Posted
Posted

Btw that's what happened to my car when it switched to e85. I got the shits with the tiny bit that was coming out with every prime so it was easier to just turn the fuel pumps on through the ecu and it took hardly any time at all to empty the tank

skins Grand Master

skins

Posted
Posted
Is there a way to turn on the pump from the powerfc hand controller to keep working til it runs out?

I had to empty mine and i used the jiggler through the boot opening. Was a pain and it stank of fuel everywhere but it got done. Then a mate said why don't you just drill a hole in it at its lowest point and then use a roofing screw ( which has a rubber seal on one end ) and put the screw in the hole. I thought that could work but didn't attempt it.

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted
On my previous car I pulled off the fuel return line and pointed it into a bucket and started the car. It then pumps all the fuel into the bucket.

this is what i do when i swap between 98 and e85

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • soviet_merlin
      Thanks Santa (the neverending trials of the 400,000klm, 400kw, RB30, manual swapped Stagea)

      By soviet_merlin · Posted

      Thanks Duncan! Yeah it's street use for me only. Maybe occasional track day. Any difference in noise when running with the two pumps? I would expect the lift pump to be more quiet than the main pump so hopefully not? And yes, unfortunately quite a big price difference to the simple hanger setup. Though I'm usually willing to trade money for better reliability and future-proofing. Buy once, cry once and all that. I'd be very happy to never have to deal with fuel pump / wiring issues again  
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
×
×
  • Create New...