Jump to content
SAU Community

Recommended Posts

  • Replies 146
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

So its a different car since since the 1.19 and even then I was only allowed to do 4 or 5 laps till they sent me home.

Since then the setup was changed to get the low 33 at Winton.

Over the coming weeks im chucking the wing on and tweeking it up a bit. Sadly the gate will have to be plumbed up ;) No more cow bell at Sandown Bris

Plus the super special Yokie will add a second im sure.

Defiantly a low 18.

Weather permitting it will have to be the John Mott sprints in July

- Roll Cages - Must be CAMS approved

- Bonnet Catches - All rear-hinged bonnets must have an additional independent non-flexible strap fitted. Permanent straps/pins attached to the bonnet are not necessary. It is acceptable to tie the bonnet down with light rope. Bonnet Pins are also accepted.

Under Vehicle Requirements are these two items necessary for every vehicle entering the event or only if you have them already then these rules apply.

yes that is cams... from what ive seen go through scrute, the cage doesnt have to have a cams sticker or anything on it.

just meet the cams requirements. its upto the guy going through your car on the day. if you get a hard ass scrute, then tough.

and yes you will need an additional restraint. the double system on post '89 (?) bonnets passes sometimes...again depends if you

get a scrute with a pole where the sun dont shine...they will want an independent restraint. (bunnings is across the road, i know from experience...)

if you dont want to screw around and argue with the, great, fantastic work :P the scrute do on the day.

drop into bunnings and get parts to make one of these up http://www.skylinesaustralia.com/forums/Se...onnet+restraint

Ok the bonnet strap is easy enough. There is one thing I find confusing and that is whether or not you need a roll cage to enter these events? Based on what was said at the start of page 2 you don't, but reading through the vehicle requirements it says you do?

I have paid to enter this event and I don't have a roll cage in my car. Can you enter without a roll cage?

Ok the bonnet strap is easy enough. There is one thing I find confusing and that is whether or not you need a roll cage to enter these events? Based on what was said at the start of page 2 you don't, but reading through the vehicle requirements it says you do?

I have paid to enter this event and I don't have a roll cage in my car. Can you enter without a roll cage?

yes you can.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • How much is it to re-uploster?  Well that's a "how longs a piece of string?" question !  And I answer thusly: "twice half its length! " . . . . . .  Seriously you'll have to chase multiple quotes for that one from different uphlostrerereres !  Ask around, in your area and on the forums, chase reviews and most of all see the finished product in person cause photoshop is a wonderful thing !
    • Hey everyone!!  I've noticed that whenever I do my oil changes, after putting 4L in, the oil level sits at the top mark in the dipstick. This is after letting the old oil drain for a very long time too! I've checked the oil level daily for the past few mornings. It happens every time and it's confusing because all the threads say that it should take about 4.7L (With some just adding the full 5L) My next thought is to figure out if the dipstick I have is correct so could someone please tell me the length of the RB25DET engine oil dipstick?  I've checked images of some of the genuine dipsticks, but none of them have the length in it. https://justjap.com/products/genuine-nissan-engine-oil-level-dipstick-fits-nissan-r34-skyline-c34-stagea-c35-laurel-y34-cedric-gloria-rb25de-t-neo?currency=AUD&srsltid=AfmBOortQXofgmiHVRKuIaiKuygL4k0Ewp68c3isGZk0vvKOJ7Yqf3iB However.... the engraving on the genuine ones say 05002 while mine says AA000. This makes me believe that maybe I have a wrong dipstick? I just want to confirm before I buy a new one. The car is a fresh import from Japan so I don't have details of the previous owner to ask him. Thanks in advance 🙏🏾 
    • Sport. I didn’t rebleed it cause I just removed the slave and left connected.    I will change line and slave and see how it goes.  
    • Oh and how is the rattle when foot is on the clutch ?
    • Did you get the sport or track ? From what the documentation says the uniclutch has a small amount of movement to disengage.  So your story of tricky pedal setup seems common.    Hopefully you got it bled up too, as the bite point moving around is usually either plates wearing in or air in the line.     
×
×
  • Create New...