Jump to content
SAU Community

Recommended Posts

Hi,

I have recently started having a problem with my series 2 R33. Sometimes the speedo does not work when the car is first started, and then after a few minutes of driving it will just start working. But sometimes it does work straight away – it's very intermittent.

I have read through the forums and have found some people have had this problem and when they have it they also have an issue with the hicas light and power steering, but I don't have this problem, it's only the speedo which is intermittently not working.

Has anyone had this issue before? Do you think it's a problem with the wiring at the back of the cluster or is it more than likely the sensor? If so – which sensor is it on the gear box? Would anyone happen to have a picture or a diagram?

Thanks.

Hey,

just an update - my boyfriend noticed that when you push the button for the trip meter reset (in the middle of the cluster) it started working. So he pulled the cluster out today for me and tightened the screws at the back of the speedo and also unplugged and replugged the wires just in case they were loose. It hasn't stuffed up again so far but if it does, does anyone have any pointers on what in the cluster has to be tightened or whatever?

Thanks!!

My tacho on the dash does that. SOmetime works, sometimes doesnt. Unlucky for me i dont have a reset bottom for tacho but i might try tighting some stuff behind the cluster and see if that helps. Oh this is a series 2 r33 as well.

  • 1 month later...
Hey,

just an update - my boyfriend noticed that when you push the button for the trip meter reset (in the middle of the cluster) it started working. So he pulled the cluster out today for me and tightened the screws at the back of the speedo and also unplugged and replugged the wires just in case they were loose. It hasn't stuffed up again so far but if it does, does anyone have any pointers on what in the cluster has to be tightened or whatever?

Thanks!!

i'm having the exact same problem with my series2. was going to have a look at the cluster this weekend to see if anything was loose. Is yours fixed now?

  • 1 year later...

an update on mine: pulled it out, looked ok, nothing loose or damaged so put it back in and it worked fine....for about a week.....couldn't be bothered pulling it out again so put up with it (wasn't really a huge deal) anyway finally got to me again, so pulled it out and re-soldered most of the connections at the back (all the larger ones with the resistor/capacitor legs sticking out) didn't expect speedo to work at all, but guess what.....fixed!! i can now go over bumps, reset my trip odometer, and break traction without it cutting out on me. so in the end it was a simple fix, no dollars required, and didn't have to replace it with a higher Km odometer (mine only has 86k on it).....stoked.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
    • So I'm in the final stages of assembling my single turbo RB30/26 and had a question regarding MAP reference points.  I've seen several recommendations such as tapping the cylinder 2/3 ITB, tapping the intake manifold at cylinder 2/3, or using a point on IAC. First two are doable but require permanently modify part and the third is "out" as I plan to delete the IAC.  All that to say my question is can I used the "bleeder" in the center of the ballance tube as a MAP Reference? I'm running a catch can so I don't need it for the PCV system. My thought process is it "pulls" from all 6 cylinder, and it's between the ITB and the cylinders making it ideal for MAP reference according to what I can find. Thoughts?
×
×
  • Create New...