Jump to content
SAU Community

Blown Seal?

dougs

By dougs,
in Engines & Forced Induction

 Share

Recommended Posts

dougs Community Regular

dougs

Posted
Posted

hey guys i'm looking for a bit of advice on my sr20det (yes i know its not a skyline lol). it appears to have a lumpy idle which the previous owner says is due to the larger s13 throttle body and lack of adjustment of the tps when it was installed, but it is now throwing up oil all over the exhaust manifold and over the front turbo housing. The car still pulls pretty hard on 16psi but there is no oil on the rear housing or the block. i pulled the alloy cooler piping off both sides and there appears to be oil in the piping pre-cooler but post-cooler it is as clean as the day it was made?? also the dipstick doesn't seem to want to stay down completely. it doesn't feel like it secures itself inside the top of the tube and whenever i pop the hood to do a check, it's usually up about 1cm.

btw its running a catch can but isn't really getting any oil in it if that changes anything.

thanks in advance guys.

Link to comment
https://www.sau.com.au/forums/topic/324095-blown-seal/
Share on other sites
  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Intro/R33 owner

      By PranK · Posted

      Welcome!  How long have you had it? And what colour is it?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      "CAD" version 1.0 It will have a 15mm lip around the top for 6 × 5 or 6mm nutserts and fixtures (two on each of the three straight edges), and some pinch weld on any exposed edges, it has three mounting points, one of the power steering reservoir bolts, and two on the rad support, my 120mm hole saw will make short work of hole for the silicone joiner, with ample room for some pinch weld  I've also got enough Carbuilders "peel and stick" heat shield to cover the outside of it at the coolant expansion tank and on the engine side, as pictured, and internally on the lid and where the fuse box is, I've also got some thin, about 3mm, black 3M single sided sticky foam stuff that was left over after sealing some door drafts at home to help seal the lid As for the shape, it "sort of" matches the shape of the fuse box, so shouldn't look to "out of place" The lower area and hole for the intake will need pinch weld with a balloon on it to fully seal the hole and bottom of it, that will happen after it has been fabricated so I know exactly what size is required  Filter service has been trialed,  and so far it was a simple process  Just need to get some alloy, and then head into work to use the guillotine and break press in the workshop Hopefully it should be sorted in a week or two Guestimated outlay will be under a $50 for the stuff I don't have on hand (alloy, 6mm nutserts, the pinch weld, and wrinkle paint) Disclaimer: That's what the "voices in my head" are telling me how the filter box should end up getting done......lets see if they know what they are talking about  
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Have been polishing up the trailer rims as they had been sitting in the shed for a few years and are really in need of some love. This was after a couple of passes with chrome polish - coming up quite well ✅ .
    • MBS206
      Intro/R33 owner

      By MBS206 · Posted

      Welcome aboard! Is your Skyline auto or manual? I'm assuming manual. Does it have any mods done yet?
    • Yeetus
      Another "where do these lines and plugs go" RB25DET question

      By Yeetus · Posted

      Hey mate, the brown and grey plugs would usually go to the TPS, brown one goes on the bottom connector and grey is the top but isn't used unless the car is auto, your TPS looks different to mine though I've got a series 2 engine.
×
×
  • Create New...