Jump to content
SAU Community

Recommended Posts

Hi there Guys,

It's been a while since i have posted a question and i have done some searching through the forums but i can't seem to find what i'm looking for.

Problem -

1995 Series 1.5 Skyline RB25DET

* Issues started with low idle - and engine stalling when cold (By the way it's an automatic) Engine would stall if any load was put on it.

* Investigated timing and all timing marks line up for 15Deg

* I've had fun by doing the following - re-Gapped sparkplugs; Got a 2nd hand CAS; Got a 2nd hand AFM; Brought new plugs

I've just been playing with the car today and managed to get it firing by itself but i had to hold my hand over the AFM to restrict the flow Engine was able to idle for 3-5secs before stalling again - I repeated the process and when firing took my hand off and died -

I'm thinking in my mind the following -=-

Either I have a break in the pipe work (Intake) but when i had my hand over the AFM the pipe was sucking in and i couldn't hear any other air. Or the AFM is cactus.

Does anyone have any other thoughts -

Regards,

Ashley Neal.

Link to comment
https://www.sau.com.au/forums/topic/324689-r33-rb25det-15-dramas/
Share on other sites

Check trouble codes then

check fuel pressure

The ECU did show me Code 55 - Everything OK -

The Fuel Pump is working - I disconnected the Feeder pipe and put into a bottle plenty of fuel went into the bottle - Is there a spec on how much presure should be there?

whats it like when its warm?

is it on a stock ecu?

if its always idling very low and is on a stock ecu, perhaps try to adjust the idle up a touch. theres also a mixture screw on the back of the ecu that you could fatten up a touch, that makes them run a little easier when their cold. But if you add fuel on base idle you will also want to up the idle screw.

GL

whats it like when its warm?

is it on a stock ecu?

if its always idling very low and is on a stock ecu, perhaps try to adjust the idle up a touch. theres also a mixture screw on the back of the ecu that you could fatten up a touch, that makes them run a little easier when their cold. But if you add fuel on base idle you will also want to up the idle screw.

GL

Hi mate,

The car seems to be racing when warm - sitting just shy of 1000rpm - when spec say's 650+/- has a slight sputter every now and again.

The ECU is a completely sealed unit with no trimpod for adjustment. I also checked for Dry-Solder in the AFM - and everything checks out there = ECU still giving Codee 55 = All Ok.

Edited by Nissan Maaaart
id go for fuel pump.

They can throw up an array of symptoms but seem ok with prelim testing like you did.

Otherwise vacuum leak...

Thanks mate, I've checked all the Intake piping and there is no apparent air leaks - does anyone know what type of presure should be coming from the rail --

I also did some further testing and with doing the following - blocking the Intake - and allowing a small vaccum of air into the AFM - the car would start with timing retarded - engine would fire on it's own for a moment - but if i removed my hand or made the vaccum less the engine would stall --

The suction from cranking felt quiet faint - can anyone comment on this?

Thanks.

did you look at all the piping cooler etc? my freind had a problem with his for 3 weeks before finding a pin hole in the intercooler.

try changing the fuel filter as well my turbo pulsar wouldnt run and idle and it was a blocked fuel filter but it still primed etc

+1 for fuel filter...im assuming you've checked your air filter..

My mates car wasnt starting, and racing at idle, i blew out the air filter with a compressor and it ran great for another couple of days..cheap prick wouldnt spend 20$ on a new one

Righto - Still Not anywhere -

I've replaced - all clamps, enusres tight- checked Cooler for leaks - new fuel filter -

And still no go - does anyone know how much New AFM's are and where to get them -- as I got a price from a crowd and it seemed a little steep at 780$ex out of Melb.

Or does anyone on the Northside of Bris have a 3 pin (Pink Lable) AFM that is known good that i could try?

Thanks.

Try a diffrent AFM had a simular problem on a mates car, Go to a wreckers or something and you might be able to test it, also AAC valve is clean? check that as well. Do you also have a BOV? or is it stock standard?

Edited by geraus

just unplug the AFM and see if it idles

the engine will run with no AFM and should idle OK, but it wont drive very well and will rev cap at 2500RPM

if the AFM is the culprit when you unplug it, it should run to normal idle

if the AFM is NOT the culprit when you unplug it, the same problem will be present and it will stall

just unplug the AFM and see if it idles

the engine will run with no AFM and should idle OK, but it wont drive very well and will rev cap at 2500RPM

if the AFM is the culprit when you unplug it, it should run to normal idle

if the AFM is NOT the culprit when you unplug it, the same problem will be present and it will stall

Hi buddy,

The vehicle wont even start - or run enough to test this theory.

I'll try the fuel line thing shortly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are adaptors that allow you to delete the booster and use an s15 clutch master cylinder.    if you want to keep the booster they are still available brand new 
    • I visited again today: It would appear they have painted the main body of the car and some parts of some of the panels, so I can say that I now have BMW parts in my car, much to the envy of @Dose Pipe Sutututu It is still covered in dust which is quite the tease but I did look at a few circumspect spots that will be behind bumpers and such and wiped some dust away: After my repeated begging to PLEASE DONT PAINT OVER THE ENGINEERING CERTIFICATE (you have to re-engineer the entire car if they do) I see THIS: Which is great. Excellent job tbh at least to me. A better non dusty example would be the backs of the doors that have been painted: Giving a reasonable contrast between old and new (I know the old isn't clear coated on the inside of doors). The door card will well and truly cover where the old paint is, you can see in the second pic some of the black butyl/whatever shit is sticking the plastic sheet behind the door transfer that has happened since it's clearly been stuck back on. The most maddening thing about this colour is every time I saw it in the wild it looks like another colour, same with photos of many cars with the same colour looking wildly different in every photo anybody ever takes and this is no exception. But stand a little further back and it suddenly looks dark AF. I did tell them when I was discussing which of the 70 million charcoal colours to choose from (a porsche one, a BMW one, or a R32 GTR one etc) that if they just ignored me and chose one at random I would probably never notice. Maybe they did. But the colour is supposed to be B39 (BMW Mineral Gray). Boring I know, but the R34 sedan (to me) really shows off it's boat-ness when you paint it in a bright colour like bayside blue or white or whatever else. I do have a fondness for AR2 Nissan Red, but decided against that because it'll have pretty odd contrast to random bits unpainted (like engine bay, bits of trim etc, and maybe it'll fade). And people will always fkin comment on AR2. Everything remains super dusty. I have tracking numbers for the new heads, as well as some Improved Racing goodies, but they probably will be a next year thing by the time they end up on the car. I did some maths on the heads and I know why nobody goes to this extent in Australia, because it's really not worth it, given I could have just CNC'ed my current heads, bought a FAST102/TB and used my current rocker/spring/cam combination and get a 383 stroker (or stroked a 6.0 GenIV bottom end to 6.6L) built for the same price of just the setup in the mail/on the floor here. Or I could have bought a LS3 and a Drysump system. And then have a complete engine to sell. Oh well
    • We just disconnected the vacuum line if I remember correctly, booster is still there. Is there a rebuild solution for the booster or a different adapter that will work for GTR chassis?
    • Yeah 4wd (boosted) has a recess in the firewall for the booster, and 2wd is flat - the example in the link shows the flat surface. When you deleted the booster, did you just attach the factory slave cylinder directly to the recess in the firewall with no adaption?  
    • Yes, but no. You need to keep the mating surfaces bare (ie the flat faces where the caliper and upright pads touch the dogbone) and also the internal threads will remain bare (unless there are no internal threads - do they use nuts on all the bolts?). So you can slow down obvious external corrosion, but not all of it. Anodising would be required to provide decent protection to the alloy, but I'm not actually sure if you should anodise something that is all about the strength. Anodising does reduce strength significantly. Like, up to 50% on some alloys for high thickness coating.
×
×
  • Create New...